Question about D-Link AirPlus Xtreme G DWL-2000AP 802.11g/b Wireless Access Point

2 Answers

Change the ip address

How to change the ip address

Posted by on

  • rpraveen May 24, 2008

    posswors error

  • smccluskey May 30, 2008

    Hello, I've tried and tried abou 10 times to setup my Dlink dwl-2000AP, but I have never been able to enter site http://192.168.0.50, I get an error message that the site is not available.

    I've tried with cd and computer attached to AP, - without cd, - through internet LAN to no avail. I just don't know what to do. Can you help me in any way. I really need to use wireless internet for my portable PC.

    THANK YOU VERY MUCH IN ADVANCE.

    P.S. I have sent several emails AND telephoned them personally, but I've had no answer to emails and they don't help by phone.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Set your computer to a static IP of, say, 192.168.0.100 and then you can connect. You can then change the ip of the dlink to what ever it needs to be as well as your computer

Posted on Nov 17, 2008

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

If your AP password erros, you can't enter the setup page of your AP in you browser. Do hard reset. Press little button behind your AP about 30 seconds. Will reset your AP to factory default, IP 192.168.0.50 subnet 255.255.255.0 user name: admin password: leave it blank.

Posted on May 25, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ip address where can i find my tv ip address


Are you sure your TV has an IP address? Not all TVs are networkable.

Like most devices, most TVs expect to be given an IP address when they connect to the network through a process called DHCP. You can probably change that in settings.

If your TV is IP-enabled, you should be able to find the network section of the menu, and find the IP address there. If you decide to manually set the IP address, be careful, because only certain IP addresses will work on your network.

Aug 16, 2015 | Wireless Access Points

1 Answer

I cannot connect to the WFC because it needs the ip adress and the connection fails


Click start type cmd press enter you will be in DOS mode
type in ipconfigpress enter you will see all of your internet connection details type in your default gateway ip adress into your internet search should read something like 10.0.0.138


Your IP Address should be thought more as your computer's phone number than it's address, if you have multiple connections, you have multiple IPs if you dont have a connection, you dont have an IP.

Without further delay If you need your computers IP address:
This will work in almost every case, it simply requests the website's server to tell you what your IP is. http://whatismyipaddress.com/
I have included a link to make things easier.

If you are in a network and need your computers local address.
Hold the windows button (looks like the windows banner, usually between left ctrl and left alt) and press 'R'.

A box will display, and type in "cmd.exe" and hit enter.
The 'command prompt' will display, a black screen with white lettering.
Simply type in ipconfig. This gives information on all your internet connections.

Look for the line "IPv4 Address".
If you need to find the IP of a current connection you can type (from the command prompt) "netstat".

This will give you all your current connections.
To identify a specific one, the easiest way is to run it before you establish the connection then again afterwards.
Change IP Addresses

Your IP address is a series of numbers that identify your specific computer on the Internet.
If, for some reason, you want to change your IP address, you can do so without going into the command prompt.Click "Start," "Control Panel," "Network and Internet" and "Network and Sharing Center."

Click "Change adapter settings."
Right-click the network you want to change and click "Properties."

Click the "Networking" tab.

Put a check either next to Internet Protocol Version 6 (TCP/IPv6) or Internet Protocol Version 4 (TCP/IPv4) and click "Properties."

Click the radio button next to Obtain an IP Address Automatically if you want Windows to assign one, or click "Use the following IP address" to manually change it.

Enter the requested information and click "OK."

Mar 01, 2014 | 2wire Wireless-G 802.11g ADSL Gateway

1 Answer

How i can change ip address of tp link 5210g throw ethernet cable


ok , need to assign your computer a Static IP address within the same
range as the AP's IP address, ip address of AP is : 192.168.1.254
the ip address for pc such: 192.168.1.253, then open your browser and write the ip address of your AP then you will be inside it .

Jan 10, 2014 | TP-LINK TPLink TLWA5210G 24GHz High Power...

1 Answer

Need to change my address


If your IP address is Dynamic,you can change it simply by resetting it.
If your IP address is Static,you can contact your Internet Service Provider[ISP] and request a new internet IP address.
You can check your Internet IP address from IP-Details.com .

Nov 04, 2013 | Wireless Access Points

1 Answer

When my wireless access point is turned on, my computer is unable to renew the ip address. I show excellend signal strength, but "little or no connectivity"


Hi, Your computer is most like have IP address permanently asign. To change the setting for windows 7, click start, click control panel, click network & internet, click network sharing, click connection, click lower left hand property, click Internet protocol version 4 (TCP?IPv4), click property and click obtain and IP address automatically. Your Router will asign IP address. Windows XP, Click start, click connect to, click to show all connection, right click to the wireless connection adapter, click the property and click the down arrow click to TCP/IP, click the property and change it to obtain IP address automatically. That should work for you. Get back to us if this information help you solve you solve the problem. Good day now.

Jul 13, 2011 | NetGear WG602 802.11g/b Wireless Access...

1 Answer

I cant get into config my dap1360 by typein in the dlinkap or 192.168.0.50


just make sure that you belong with in the same IP range.
default DAP-1360 IP is 192.168.0.50
username : admin password : <blank>
change your PC IP address to 192.168.0.xxx (e.g. 192.168.0.2)
from there you may choose wizard or manual configuration.
you may change your DAP-1360 IP add according to your network settings in the office and you must change you PC IP address with in the same range.

Mar 24, 2011 | D-Link DAP1360 IEEE 80211n (draft)...

2 Answers

I cant set up my http://192.168.0.50/ address and i dont know how to set up an IP address ???? how do i do so?


If you need to set and IP address on you PC:

-goto LAN devices, click properties on yourLAN, scroll down and select Internet Protocol (TCP/IP), clickproperties, click set and type follow IP address:

IP: 192.168.0.1
Subnet: 255.255.255.0
Default Gateway: 192.168.0.50

Noew click, OK, OK,... to confirm all you changes.

Oct 15, 2009 | D-Link AirPlus Xtreme G DWL-2000AP...

1 Answer

I get an IP conflict error message.


Dear you havent mentioned that you are on wireless or on Lan.
any way... issue is that your both systems have the same ip addresses and now you have to change ip address of any one of them..
i recommend you to change ip address of your desktop computer.

here is the way to change it...

  1. Click Start, click Control Panel, click Network and Internet Connections, and then click Network Connections.
  2. Right-click the network connection that is connected to the private ICS network, and then click Properties.
  3. On the General tab, click Internet Protocol (TCP/IP) in the This connection uses the following items list, and then click Properties.
  4. On the General tab, click Use the following IP address. Configure the entries as follows: (if the option is selected that "obtain the ip automaticaly" then leave dont follow the given instructions and msg me again)
    • IP Address: . just change the last value of your ip address. say its 192.168.1.20 .. change the last value to any other two digit value..
    leave the other configurations as it is.
  5. Click OK.
  6. Click Ok
Now try it..


Rate me if you think it helps you..

best regards,

Tanveer Ahmad Khan

Dec 14, 2008 | Wireless Access Points

1 Answer

Cannot log on to dwl2000ap


If the SSID changed to the default then you know that the router reset to the default settings and you should set your computer to automatically get its IP address via DHCP. I always set up my routers through a Wired connection first, just to setup the router and then go with the wireless. The default for the router should be 192.168.0.1 and subnet 255.255.255.0 . If the computer is set with a static IP address, change it to obtain an IP address automatically or the network card will not bother even looking for an address.

Aug 17, 2008 | D-Link AirPlus Xtreme G DWL-2000AP...

3 Answers

Dynamic IP address


Dynamic ipaddress - is temporary, the ip changes when you disconnect for example.

Normal, or static ip - It's the same address from day to day.

May 19, 2008 | Wireless Access Points

Not finding what you are looking for?
D-Link AirPlus Xtreme G DWL-2000AP 802.11g/b Wireless Access Point Logo

Related Topics:

530 people viewed this question

Ask a Question

Usually answered in minutes!

Top D-Link Wireless Access Points Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

scramblepad
scramblepad

Level 2 Expert

66 Answers

Anthony Chiang
Anthony Chiang

Level 3 Expert

524 Answers

Are you a D-Link Wireless Access Point Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...