Question about Honeywell HHT-090 Air Purifier

3 Answers

Red light won't go off

I vacuumed the filters as instructed - but the red light is still on. What's up?

Posted by on

  • Anonymous Feb 23, 2009

    The red light won't go off on my honeywell air cleaner even after being cleaned several time?

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

To RESET the Electronic Filter Check:
When the filter check light remains on,it is time to check/clean the HEPA-Type
filters and reset the filter check,if needed. With the unit powered on,insert the tip of a ball-point pen or
paperclip into the hole next to the LED filter check light and hold for approximately 5 seconds until the
light turns off (Fig 5). Depending upon your individual usage (environment and hours used),you may need
to check and clean the filters more or less frequently. If the HEPA-Type filters are cleaned before the filter
check light turns on,the filter check should be reset at the same time.
These cleaning intervals are intended as guidelines only. Performance of any filter media is dependent
upon the concentration of contaminates going through the system. High concentrations of contaminates
such as dust,pet dander and smoking will reduce the useful performance of the filter.
NOTE:The HEPA-Type filters are not washable.
Fig.5

Posted on Oct 05, 2009

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I purchased a Honeywell Model HHT090 and I have cleaned the filters and the red light still will not go out. What can I do to ge the light to turn off. It says to vaccum the permanent pop in filter and I have done so and he red light is still on. What can I do !!!!'

Please Help !!!!!!!!!

Kellie

Posted on Nov 27, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I am also having a hard time -- my hepa (something-600?) filter's red light is continuing to stay on despite pushing the reset button various times and lengths of time. I tried switching it off and then on again. Looked at filter, installed it a few weeks ago (new), made sure everything was put in correctly and clean.
Cannot find a reason for the red reset button to still be on!! Very frustrating. :(((

Posted on Feb 01, 2016

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my Kenmore intuition vacuum 31810 Red light stay on ?


Here's a couple options
http://www.ehow.com/way_5513470_kenmore-vacuum-troubleshooting.html
http://www.shopyourway.com/questions/1128413

Jul 28, 2014 | Kenmore Intuition 31810 Upright Bagged...

1 Answer

How do you change the filter? My in-laws have lost the instructions for their purifier.


You have a Honeywell air filter. Turn it over and there is a big handle which is a screw in the middle. Unscrew it and then lift the entire unit up without the outside screen protection. The filter will have a black pre-filter attached by velcro. Remove it, take outside put on the grass and hose out against the flow of air. (squirt from the inside out to remove stuff). Then use vacuum to blow the filter from inside to the out. Then vacuum the filter from outside in. Let the pre-filter dry. re-install in reverse. If there is a warning light, run on full, then push the warning reset for 10 seconds or more to turn it off.

Mar 01, 2011 | Duracraft DA5010 Air Purifier

1 Answer

Mother gave me her filterqueen defender.. no manual. 360. There is a flashing red light even though its a new filter. Why?


The light is a reminder to change the filter, it does not sense if the filter has been changed or not.
When the red light is blinking, press and hold both up and down arrows until the red light blinks RAPIDLY, release both for a second or two, and press and hold both again until it stops blinking.

Dec 28, 2010 | Filter Queen Defender Air Purifier

1 Answer

V5 filter replace - how to reset red flashing light?


Hello,

So after you have replaced the V5 Cell Filter in the IQ Air, here are the steps you'll need to follow in order to reset the filter indicators:

  • At the main menu on the control panel, push the menu button 7 times until you get to the screen that says Replace Filter.
  • At the Replace Filter screen, press and hold the Enter Key until the cursor appears, and is flashing.
  • Press the UP arrow button on the keypad until you get to the V5 Cell Filter.
  • At the V5 Cell Filter screen press the Enter Key to confirm your filter reset selection. This will turn the corresponding filter LED to a flashing red light. IQAir requires that your reconfirm the filter selection to prevent inadvertently resetting the wrong filter. If you chose the wrong filter, press the menu key after pressing the enter the first time to disregard the filter change command.
  • To confirm the filter reset selection, press enter a second time, which will reset the filter life, and reset the filter hours.
You can repeat these instructions for the other two filters on your machine when it's time. Here's a link to the product manual for your IQ Air Health Pro Plus which will give you the same instructions, as well as other maintenance instructions.

http://lib.store.yahoo.net/lib/vacuumcleanerbacgs/IQAir-healthpro-plus-owners-manual.pdf

I hope that this information was helpful to you. If you were able to reset your filter, please be kind and rate the repair as helpful by clicking the thumbs up icons in the top of my repair. This is what really keeps Fixya experts continue leaving free repair solutions. Thank you very much,

Chris J.
GoVacuum

Apr 08, 2010 | IQAir HealthPro Plus Air Purifier

1 Answer

Brookstone pure ion filters


You need to reset it, unplug the unit and take out both filters. Then, plug it back and and simultaneously and firmly slam both filters into the back of it at the same time. Before putting both filters back inside the until, also vacuum out the insides in case there is hair/dust inside of it that has accumulated.
Also, make sure your filters are 100% dry before every putting them back inside the unit.
Good luck!

Mar 02, 2008 | Brookstone Pure-Ion UV Air Purifier

3 Answers

Red light on air filter


After spending hours searching for this supposed little hole easy to miss, I called customer service. I found out that it's easy to miss because it doesn't exist!

Here's the correct answer: Once you've replaced the filters, turn the unit back on. Then, with the machine running, press and hold down the on/off power button for about two seconds. The red light will flash and then turn off.

Oct 12, 2007 | Holmes Products HAP422-UC Air Purifier

2 Answers

Red light


Here is the link to the user manual; http://www.filterqueen.com/pdf/defender.pdf The red light indicates a filter needs replacing, see page 6 of the manual (page 9 of the pdf file) If filters have been replaced and the light still flashes, then the reset procedure (described on the same page) should work. If still flashing then there is a more serious, but probably fixable fault. Hope this helps - ask again if you need more info :)

Apr 13, 2007 | Filter Queen Defender Air Purifier

7 Answers

Red Light indicator on


I have a Bionaire tower air filter model BAP1700 that I bought from Costco. The filter check LED came on recently after 5 months of use. After cleaning the Permatech filters, I tried every remedy on this website including following the instructions that say push power button for 2 secs. Nothing worked. Then I noticed a tiny hole on the control panel in front of clean filter LED; I pushed a paper clip pin into that hole, felt a click, held it down and 2 secs later, LED went out. Success!

Apr 06, 2007 | Bionaire BAP1500-U Air Purifier

3 Answers

Red Light on front of Filter Queen Defender


When the red light is blinking, press and hold both up and down arrows until the red light blinks RAPIDLY, release both for a second or two, and press and hold both again until it stops blinking. It cured my problem.

Mar 06, 2007 | Filter Queen Defender Air Purifier

Not finding what you are looking for?
Honeywell HHT-090 Air Purifier Logo

4,396 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honeywell Air Purifiers Experts

Bill Long

Level 3 Expert

577 Answers

Cindy Wells

Level 3 Expert

4759 Answers

Jay Finke
Jay Finke

Level 3 Expert

1222 Answers

Are you a Honeywell Air Purifier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...