Question about Garden

1 Answer

I have an N62FN-2 that doesn't drive nails all the way in. It leaves 3/8" of each nail exposed @ 100 PSI. When I release the gun without a nail loaded, there is no indentation.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,865 Answers

Increase the pressure to 105psi and test it again. J.

Posted on Sep 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My hitachi nt50ae2 will not work with 2" nails no matter what brand I use.


1. Have you adjusted the air pressure to at least 100 PSI?
2. Have you cleaned and lubricated the gun per manufacturer's instructions?
3. Are you driving nails into hard wood (oak, walnut, etc.)? Some guns are simply not powerful enough to handle extremely hard woods.

Dec 02, 2017 | Hitachi Tools & Hardware - Others

1 Answer

Why might my nail guns not work?


Have you lubricated either nail gun? If not, go to Home Depot and get a bottle of air tool oil. It's in tools by the compressors. Disconnect the air hose from the tool. Pour about a teaspoon of oil into the air inlet of the tool. Reconnect everything and try it 10-20 times with no nails in the tool. Then try it with nails. Good luck.

Sep 14, 2015 | Porter Cable Tools & Hardware - Others

1 Answer

Why wont my hatachi nail gun shoot 1 3/16 nail all the time


Has the tool been lubricated properly to Hitachi's recommendation? Is the airline pressure running about 90-100 psi? If not try giving it more pressure. Sometimes the compressor may have too smaller receiver (Tank) for what you are trying to use it for, leaving the tool unable to return the piston/driver to top dead centre.

Sep 13, 2014 | Tools & Hardware - Others

1 Answer

How do I release the trigger lock on a brand new porter cable nail gun


Are you depressing the nose of the nail gun against the material to be nailed first? Without doing this, the trigger will not "unlock". You can read a pretty in-depth review of this nail gun at OnlineToolReviews com Porter Cable FR350A Full Round Head Framing... which might also help.

Jul 16, 2014 | Porter Cable FR350A Factory Reconditioned...

1 Answer

Nail gun 58-8434-4 will not drive 3" nails all the


Hi foxden503,

Welcome to fixya!

As a general rule, framing nailers use anywhere from 45 to 120 psi to drive nails. But this also depends on the hardness of the wood.
The nail head should be flush with the surface. If it sticks above the wood, increase the pressure a little bit at a time until you achieve this goal.

Hope this helps. If it does, I'd appreciate your vote. Thanks,

Handie Andie

Jul 20, 2011 | Tools & Hardware - Others

1 Answer

Adjusting airpresure


There is nothing on a nailer to adjust the air pressure. You have to do it at the pressure regulator. It is feasable to mount a regulator at the gun but more likely it's on the compressor. Most nail guns are rated for 90 to 120 psi. Set your regulator to hold the hose pressure between 90 and 100 psi. Using higher pressure to set the nail will ruin your nailer. Use the depth adjustment on the gun to set how far the nail is driven.

Sep 23, 2010 | Nailers 3 12" Pneumatic Air Round Head...

1 Answer

GUN NOT SETTING NAILS


Hello jsc.... the depth that the nailer drives the nail is dependent upon two factors, the hardness of the material you are driving the nail into and the air pressure. Generally when you want the nail to go in more you adjust the air pressure to a higher setting, going 5 psi at a time until you are close to perfect and then fine tuning the air pressure.

Sometimes people find that the air compressor itself is inadequate for the job. in that case, the only choice is to move up to a higher psi compressor. Joe

Thanks for choosing Fixya!

Jul 04, 2010 | Hitachi 3 - 1/2" Full Roundhead Framing...

2 Answers

Porter Cable BN125A won't set nails below surface


Not sure about the seal, but I do know the pressure has to stay up for this nailer to be effective. Try oiling the gun to free up the mechanics and don't use old nails.

Jan 23, 2009 | Porter Cable Cable BN125A Factory -...

Not finding what you are looking for?
Garden Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garden Experts

Dennis Key
Dennis Key

Level 3 Expert

2478 Answers

roeb

Level 3 Expert

708 Answers

john h

Level 3 Expert

14331 Answers

Are you a Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...