Question about Kenmore Dryers

1 Answer

Hello, It seems my dryer's control panel doesnt work..I press the start button a few times and then it will turn on, but turn off after 10 seconds. It takes a long tiom, before I can turn it on and I press the start button until it can turn on and then it turns off after 10 seconds .Is there a way I can reboot the control panel?

Posted by on

  • dustymirror Sep 27, 2010

    Please provide the complete model number so a tech can better answer your question, thanks.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 176 Answers

Check the door or door switch

Posted on Sep 27, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Intermittent Start (expanded explanation)


Lint will jam the start/run switch on the motor. Vacuum out the motor real good and check that the switch moves freely, and all the wires to it are plugged in good.

Nov 30, 2013 | Maytag Dryers

1 Answer

When pushing the start button the dryer will come on for about 10 minutes and then stop. Then sometimes it doesnt come on at all


If it starts right back up after stopping there is an electrical problem maybe at the motor start switch. If you have to wait for an hour before it will start again then the problem might be that the motor needs to be cleaned of a lint build up.

Oct 23, 2012 | Roper RES7646KQ Electric Dryer

1 Answer

My dryer is dead. I have ohmed out the cord and changed the dryer control board (8546219). Still dead, nothing at all. Any other ideas? I have checked the fuse and it is good. I had a local repair man look...


hello again,

no thier doesn't seem to big issue with with reconditioned control panels in fact i dare say yours is good since the dryer didnt start with the original one and still wont start with the one you have replaced. having checked teh thermal fuse to be good and with basically 2 control boards yet the dryer doesnt run it seems very possible the motor is going to be the problem...not sure what led ya to the control board yet it the drum doesnt turn the very part that turns it when power is applied to,if it has powewr to it and doesnt turn the drum it would seem to me its bad....dont get me wrong on this but its like having a broken leg and going to the doctor and saying i believe that my heart is weak since my legs hurts and totally disregarding the broken leg


GENE

Oct 04, 2011 | Kenmore Elite HE4 Electric Dryer

1 Answer

I have a frigidaire affinity dryer that will dry for a few minutes then turn off and say e68 wich means one of the buttons are stuck i took the panel of the front and checked the buttons and they all seem...


Run the service diagnostic mode to determine which button is stuck. Start by pressing and holding the Select and Cancel buttons simultaneously for 6 seconds to reset the control.
jahn27_112.jpg

Rotate the cycle selector knob 5 turns counterclockwise to the second position from the bottom immediately after the buzzer sounds.
jahn27_113.jpg

Press and hold the Options and Cancel buttons simultaneously for 2 seconds. The control enters the test mode and the buzzer will sound 3 times with all of the LEDs flashing.
jahn27_114.jpg

Rotate the cycle selector knob 4 turns clockwise to the second position from the top and the dryer motor runs with the heating element off. The buttons can now be tested to determine which is stuck.
jahn27_115.jpg

Press each button and all corresponding LEDs should light. If the LEDs corresponding to a certain button lights up without pressing the button or if the LEDs do not light up when the button is pressed, that button must be stuck or not making any contact when pressed.
jahn27_122.jpg
jahn27_116.jpg
jahn27_119.jpg
jahn27_118.jpg
jahn27_120.jpg
jahn27_121.jpg

Replace the control board if the stuck button cannot be unstuck or if there's no button that's apparently stuck but the fault code persists. Let us know if you need further advice.

Feb 01, 2011 | Frigidaire Dryers

2 Answers

Samsung washing machine F1245 control panel stuck??


I have Samsung/korea-SW905Washer.When power is switched on the Fault-'1E' appears. what could be the reason.( narrate list of control component failure).
Bought in the year 1996 at India ( voltas mega washer top loading-7.5kg) and working till last month.
after few wash cycles the machine stopped at aforesaid indication and it is not functioning due to above fault indication'1E'
provide me remedial measures or electronic control board circuit.

May 29, 2009 | Samsung WE356A5W Washer/Dryer Laundry...

1 Answer

Kenmore HE2 Gas Dryer Control Panel Does Not Work Properly


I have the same problem..really disappointed in this product. I bought mine in 07 as well..I found that if i hold all the buttons down and then hit start it (Sometimes starts), but after it starts it turns off after 10 seconds.

Mar 27, 2009 | Kenmore Dryers

2 Answers

Kenmore Elite HE4 beeps three times when start panel is pressed and wont turn on


FWIW ... the Sears guy came by yesterday. The problem was apparently that the door latch was not operating to the extent that the sensors thought the door was open. He is replacing the latch next week. He adjusted the old one in the mean tiome and it appears to be working fine.

This kind of stunned me, since my wife reported an electric zap and the interior light burned out as the dryer went dead -- so I was sure it would be a fried circuit board -- but, no, a little jiggling of the latch seemed to clear it up....

Jun 24, 2008 | Kenmore Elite HE4 Electric Dryer

2 Answers

Kenmore Elite HE3


replace the power control board

Jan 21, 2008 | Kenmore 82822 Electric Dryer

Not finding what you are looking for?
Dryers Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Tim Whalen

Level 3 Expert

3072 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

Are you a Kenmore Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...