Question about Maytag Neptune MDG5500AW Gas Dryer

1 Answer

Livechat follow up.

Dear Gary, I just posted a message to you through the livechat page, and actually your help hasn't solved the problem yet. I cleaned out all the lint, but am still having the same problem. The dryer turns on and spins, but no heat after 5-6 minutes. (It does get warm initially).

I also wanted to know, did the $20 I paid cover just that first chat? I was under the impression that we could livechat until the problem was solved. I had to go to work the day before and I couldn't go back to the chat.

My email is Rikkydog@gmail.com. Thanks for your help.

Rik

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 770 Answers

Althought you cant go back to chat
I am willing to keep going with you to fix your problem via emails plz post your here so we can fix your dryer
Thanks Gary

Posted on May 22, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i find out what the frigidaire gallery series dryer error messages are


Hello Friend, this is Z. I appreciate your post!

To get the error code your dryer may be experiencing, attempt the following:

Wake your dryer by pressing any button except for CANCEL.

Press and hold the "CANCEL" and "START PAUSE" buttons simultaneously for 6 seconds to show the error recorder code your dryer may have. The error code normally appears in the display as an E followed by two numbers.

If your dryer shoes, E00 it indicates no failure code was detected.

I ask that you please follow up with a comment on the post, at your convenience, to advise if you receive an error and if further troubleshooting is needed.

Thank you!

Jul 17, 2014 | Frigidaire Dryers

1 Answer

Just bought this dryer how to use?


Dryers come with a little booklet. Open the booklet to the page that says ;HOW TO OPERATE then READ

Best of it
Gary @ Fix Ya

Jun 07, 2011 | Dryers

1 Answer

What does the fault message "F dL" mean?


"Fdl" is a lock latch error code. This is an indication of either a defective door latch, defective Central Control Unit (CCU), or an interconnecting cable problem between the two. The following link explains:

http://www.fixya.com/support/r4490349-fdl_error_code

I have included parts resource websites in the link provided, if parts are required. If you have any questions, please post with your MODEL NUMBER and let me know. I hope this helps you.

May 03, 2011 | Whirlpool Duet 7.0 Cu. Ft. Super Capacity...

1 Answer

We need to know where the tension pulley goes and we need a diagram to show us how it goes in


You can view an extensive list of dryer belt diagrams at the following website:

http://www.repairclinic.com/Dryer-Belt-Diagrams?red=Dryer-Repair-Help

The diagrams are listed by manufacturer and model. If you still need assistance in determing which diagram to use, please post back with your MODEL NUMBER and let me know. I hope you find this information helpful.

NOTE: If the link does not work for you, go to repairclinic.com and click on the "Get Repair Help" link at the top of the page. Select "Dryer", followed by the "Click here for belt installation diagram" link.

Nov 23, 2010 | Dryers

1 Answer

Need to replace the dryer belt and have the dryer taken apart, how do i put the belt back on?


Thre are a couple of different ways, the dryer belt goes back on a Whirlpool manufactured dryer (including Kenmore). However, since you posted no MODEL NUMBER, I can only give the following advice:

Go to repairclinic.com and click on the "Repair Help" link at the top of the page. On the following page, look for the "Dryer Belt Diagrams" link under the "Special Features" section. Refer to diagram H or K.

If you aren't sure which configuration to use, please post back with your model number, so I can provide you with a more difinitive answer. I hope this helps you.

Jan 21, 2010 | Dryers

1 Answer

I have my kenmore 80 series dryer apart, and i am replacing the belt. having trouble configuring the belt around the pulley and motor, since the belt cannot actually go into the pulley, its sealed. help.


Kenmore dryers are configured in several different ways as far as the location and routing of the dryer belt. For drawings of how the belt is configured on your dryer, go to Repairclinic.com and click on the "Repair Help" link. On the following page locate the "Dryer Belt Diagrams" link under the "Special Features" section. Scroll down to the Kenmore section and refer to diagrams H, B, or K. If you are not certain, please post back with your complete model number (located on a nameplate around the door opening) and I can determine for you. I hope this helps you.

Oct 23, 2009 | Kenmore 62622 Electric Dryer

1 Answer

The internal fitting for the door catch has broken. What is the part called and are there instructions for replacing it?


Hi Gary, It is called a door latch...
Try this website Gary, they will probably be able to help you get the part and install it.
They also have a live chat assistant that can answer your questions 24/7

http://www.appliancepartspros.com/Appliance-Parts/Dryer-Parts/Door-Latch-Kits/index.aspx

Or this one, they also have a chat assistant that may be able to help you.
http://www.partselect.com/


Good Luck,
I hope this helps

Oct 17, 2009 | Hotpoint TFA34 Electric Dryer

1 Answer

Do you have a routing diagram for the belt?


Go to repairclinic.com and click on the "Repair Help" link. On the following page, look for the "Dryer Belt Diagrams" link under the Special Features secction. Whirlpool is listed as either diagram H or K. If you need help in determining WHICH diagram to use, post back with your complete model number (located around the door opening) and I can tell you. I hope this helps you.

Oct 01, 2009 | Whirlpool LGB6300 Gas Dryer

1 Answer

Belt diagrahm


Go to repairclinic.com and click on the "Repair Help" link. On the following page, locate the "Dryer Belt Diagrams" link under the Special Features section. Refer to diagrams H, B or K. If you need assistance in determining which diagram you need, post back with your model number and I can assist you better. I hope this helps you.

Jul 23, 2009 | Kenmore 73952 Gas Dryer

Not finding what you are looking for?
Maytag Neptune MDG5500AW Gas Dryer Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Dryers Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Tim Whalen

Level 3 Expert

3056 Answers

Are you a Maytag Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...