Question about Pioneer PRO-710HD 64" Rear Projection Television
After I turn on the tv, it works for few minutes, next the screen goes blank with no sound.. after I turn it off for a while, the TV works again. Is it a power supply problem ? I took out the power supply board but could not find any broken solders.. thx, Ravi
If you are still running your set with the
intermittencies happening occasionally, TURN IT OFF NOW
AND UNPLUG IT UNTIL TIME TO REPAIR THE BOARD! If it
has shown signs of occasional malfuction and you are
still running it, you are playing Russian Roullette
with your multi-thousand dollar investment.
if you are currently using your set while it's in this
compromised condition of blue flashing, inconsistent
brightnesses, shutdowns - not only are you
risking a ground letting go on a regulation circuit,
causing your voltage to go into runaway, but
you are also risking spikes going directly downline to
the rest of your set. Hinky connections
cause spikes. There's no way to protect the rest of
your set from these spikes by installing a
surge protector on your main power plug, which is way
too far away from the circuitry concerned,
downline from the PS board, to be of any help. The PS
board has spike filtering on the incoming
120v from the wall plug, but that doesn't matter
because it delivers its results DIRECTLY to the
rest of your set, and the same filtering does not exist
at the tail end of the PS board, only at
the nose/incoming end.
If you get a new PS board, there will be a new set of
high precision voltages going downline to the rest of
your set from it. The original voltages are what the
set was set up on originally, they were sent downline
from the original power supply bd to the rest of the
circuitry, where everything was set up according to
them. Voltage regulation is generic, and only has to
wind up being within certain parameters, which means a
great deal of difference may be there among the
voltages, between the old board and the new board.
As such, I do not recommend getting a new board from
Pio for this purpose on the x10 models of Pioneer
Elite, like this one, and some of the x20 models, which
used the same PS board. I instead recommend
having the original PS board resoldered by someone who
knows the ins and outs of how to do so without creating
solder bridges in the super small connections – which
are all over that board, and in massive quantities. It
is not a job for the faint of heart, nor the
inexperienced or ill-equipped. I am the only service
repair tech I know of who is doing what needs to be
done with this board, tho some DIYers claim to have
done so as well. Others have found the board they
resoldered has gone out later, when they didn’t do it
to the level at which I do it. Boards I resolder don’t
go bad weeks, months or years later, like the original
Pio board has done. And like those resoldered by many
DIYers have done. When I resolder that board, I bring
it to the level the other boards in there are already
at - continuous non-problematic use from then on.
There are many boards in there, yet THIS one is the
only one with the problems. This was due to an
inadequate solder flow job way back when the unit was
originally produced. I cure that problem permanently.
DIYers can do it too, as long as they have the
comprehensiveness, dedication, persistence and patience
it takes to do it to the level at which it needs to be
done. Not everybody has that.
If you would like me to do the resoldering op on your
board, contact me directly and I'll send you the proper
info on how, where to send it to, and how much it
costs. Hint - it costs less than getting a new board
from Pioneer and having a local Pioneer authorized
facility install it for you.
email: bob at imageperfection dot com
Posted on Aug 01, 2008
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Tips for a great answer:
Jan 28, 2016 | Samsung Televison & Video
Dec 20, 2015 | LG Televison & Video
Jan 12, 2013 | Samsung LE32B450 32 in. LCD TV
Jan 06, 2011 | Toshiba 42HL167 42 in. LCD Television
Jun 07, 2010 | Polaroid TLA-01511C 15 in. LCD Television
May 13, 2010 | RCA L32HD32D 32 in. LCD HDTV
Jul 14, 2009 | Samsung HP-S5053 Television
Jul 20, 2017 | RCA L32HD32D 32 in. LCD HDTV
Nov 22, 2007 | Televison & Video
Mar 16, 2017 | Pioneer PRO-710HD 64" Rear Projection...
68 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: