The power blinked and now the 3 in 1 printer will not turn on. I reset the surge protector and it's like it's not even plugged in.

Re: Bravia KDL46EX720. Red LED blinks 4 times and TV wont turn on. What is the problem?

Do a Power Reset.

1. Turn off the TV.
2. Unplug the power cord of the TV from the electrical outlet.
3. Let the TV remain without power for 60 seconds.
4. Plug the power cord back into the electrical outlet. (If the television is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the television.)
5. Turn on the TV.

If the issue still persists after performing power reset, that may be an indication that the TV needs service. You may refer to this link to locate the nearest Sony authorized service center in your area.

1. Check the power cord is plugged in properly by removing it and replacing it. 2. Try a different outlet on the surge protector.3. Most surge protectors have a reset button, try resetting it.
Is the sound bar the only device plugged into the surge protector?

Need to know how many times the led is blinking.

Try this link for more information

Re: tv kdl-55ex620 red light blink 8 times Do a Power Reset. 1. While the TV is off, unplug the power cord of the TV from the electrical outlet. 2. Let the TV remain without power for 60 seconds. 3. Plug the power cord back into the electrical outlet. (If the television is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the television.) 4. Turn on the TV. 5. When the TV powers on and a picture is displayed, reset the TV to factory default settings.

• If the Reset message does not appear and the TV turns off and on, begin again from step 5.

• If the standby light begins blinking eight times, return to step 1.

6. After the Reset message appears, allow the TV to reset. Do not press any buttons on the remote control or on the TV and do not make any other adjustments for 1 minute. 7. Unplug the power cord from the electrical outlet. 8. Allow the TV to remain without power for 10 seconds. 9. Plug the power cord back into the electrical outlet. 10. Turn on the TV.

• The initial setup screen displays if the above procedures were performed correctly.

11. Follow the on-screen instructions to complete the initial set up. 12. Perform a system software (firmware) update.

try removing all power cables of your computer that are connected to the surge protector. reset the surge protector. wait for about 5 minuets before you turn on the surge protector. then plug all cables that your remove from your computer the turn on the computer.

Please follow the below troubleshooting steps: 1. If the Television is plugged into a surge protector, remove it from the surge protector and plug it directly into the wall outlet. 2. Try connecting the TV to a different AC wall outlet. 3. Try power resetting the TV. To Reset the TV, disconnect the power cord for a short period of time (approximately 1 minute), then reconnect the power cord and power ON the TV. 4. If the issue still persists, TV will require service.

The STANDBY light will flash if the television detects an issue within the television. Some of these issues can be resolved simply by following the steps below to reset the television.
If the issue is still unresolved after following all of the troubleshooting steps, Service will be required. Please note the number of times the STANDBY light flashes and relay that information to the service center.

1. Turn off the television. IMPORTANT: For a projection television that uses an internal lamp, wait 5 minutes after turning off the television to allow the lamp to cool before continuing with the following steps.
   
2. Unplug the television power cord from the electrical outlet.
3. Let the television remain without power for 60 seconds.
4. Plug the power cord back into the electrical outlet. NOTE: If the television is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the television.
   
5. Turn on the television.

plug in a light into surge protector and see if it works if not surge protector is bad or battery is shot if it has one!!i have numerous surge protectors that went bad try plugging printer into wall outlet and if working its surge protector!!!

Hi, if this TV was hit by the surge and it was protected by a surge protector, please follow this reset procedure.

The STANDBY light will flash if an issue is detected within the television. This can sometimes be resolved by simply following the steps below to reset the television.

1. Turn off the television. IMPORTANT: For a projection television that uses an internal lamp, wait 5 minutes after turning off the television to allow the lamp to cool before continuing with the following steps.
   
2. Unplug the television power cord from the electrical outlet.
3. Let the television remain without power for 60 seconds.
4. Plug the power cord back into the electrical outlet. NOTE: If the television is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the television.
   
5. Turn on the television.

If the problem is still there and the light is still blinking 4 times, this means that the surge has destroyed the Vertical deflection component. in this case, it will have to be replaced.

please rate and have a great day.

Sounds like your power supply may be shot on your computer. You can get a power supply tester and check it. Not sure what to do about the printer. If you had a surge protector in between your computer and ac. Plug the computer and printer back in to the AC outlet directly and see if that helps. Hopefully only your surge protector is damaged.

Please rate, Thanks.

Step-1: Connect the All-in-One directly to power outlet
--------------------------------------------------------------

The surge protector may not supply sufficient power to the printer. To isolate the issue please remove the power plug of the printer from the surge protector and connect it to the wall jack directly.

Being a All-in-One Machine it needs full voltage to be supplied while initializing Surge protectors supply suppressed voltage to the printer which leads to unexpected issues in the printer

After performing the steps, please perform the steps below.

Step-2: Power Cycle the All-in-One
---------------------------------------

Follow the steps below to power cycle your all-in-one:

1. Verify that the unit is switched on. Disconnect the USB/Ethernet cable from the All-in-One and also disconnect power cable from All-in-One and also from wall outlet.

2. Wait 30 seconds.

3. Plug in the power cable to All-in-One and also to wall outlet.

4. Check for the functionality.

After performing the above steps if issue persists, please perform the below steps.


Step-3: Reset to Factory defaults
-------------------------------------

A partial reset will return user settings to factory defaults. On some models, language and country/region settings are also reset. Perform a partial reset of the product by following the instructions below.

1. Unplug the power cord from the unit.
2. Do the following according to your specific product:
   • HP Officejet G55 and G55xi series: Press and hold Minus ( - ) and 3 while plugging in the power cord.
   • HP Officejet G and K series:
   • Press and hold # and 3 while plugging in the power cord.
   • HP Officejet T series: Press and hold * and 8 while plugging in the power cord.
   • HP PSC 700 series: Press and hold Cancel and the Left Arrow while plugging in the power cord.
3. While still holding the buttons down, plug the power cord back in. Release the buttons after the all-in-one begins to initialize. After RESET displays and the printer goes back to a ready state, the reset is complete.
4. Try the print job again to see if this step resolved the issue.