Question about Canon PIXMA MP830 All-In-One InkJet Printer

1 Answer

Canon PIXMA MPA830 power loss

... And when I got up this morning, the printer was dead. No power.

I tried leaving it unplugged for hours, then re-powered, but still... dead.

No power surges, worked fine until this morning. Thirteen months old.

Any suggestions, pleeeze?

Posted by on

1 Answer

I had a similar problem after a power surge. But when I left it unplugged for 10 minutes and then plugged it back in it powered up just fine.

Posted on May 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Canon pixma mx 340, it is less then a year old and will not power on, unplugged and tried new power cord and still nothing.


hi did you mean dead set?check the fuse on the power supply.you can see it by opening the the back to where the power cord is inserted..replace the fuse if blown..

Jun 27, 2011 | Canon PIXMA MX340 Wireless Office...

Tip

No Power? Do this.


My PIXMA MP530 seemed unable to get power. I checked all the connections and couldn't get it going. A call to Canon was to result in them sending me a new printer until after a second call I got a technician who suggested the following and it worked!

Unplug the printer and wait at least an hour. After an hour plug it directly into a working socket.

Apparently there is a transformer that has to have the unplugged time to be able to reset (or something).

Anyway it worked and saved me a whole lot of hassle.

on Jul 31, 2008 | Canon PIXMA MP530 All-In-One InkJet...

1 Answer

My canon pixma mp620 is plugged in,switched on but will not print. error message reads "printer not responding"


unplug the printer from all source of power supply ,leave it for like 15min then plug it back.make sure the printer is proberly connected

Jan 10, 2010 | Canon PIXMA MP620 All-In-One InkJet...

1 Answer

Printer does not power up.....


check out the power cord or replace the power cord with new one

Nov 27, 2009 | Printers & Copiers

1 Answer

Remove printer head in PIXMA MX850 when there is no power


You could take it apart to get it out but be aware of the high voltages contained inside printer capacitors. You need to leave it unplugged for at least a week to allow the capacitors to discharge.

Sep 21, 2009 | Canon PIXMA MX850 Multifunction Printer

1 Answer

Flashing 3 times orange then green?


4 step to Reset waste counter CANON PIXMA iP 1500
STEP 1:- Disconnect printer from AC power(unplug it from all source of power supply leave it for 5min then back after))
STEP 2:- Press and HOLD the POWER button, and connect printer to AC power
STEP 3:- release the the POWER button
STEP 4:- Press the POWER button again

Mar 31, 2009 | Canon PIXMA iP1500 InkJet Photo Printer

1 Answer

It will not turn


Try leaving it unplugged for 1 hour plug it back into a different wall outlet and the power supply should then come back to life. If not take it to a canon service center.

Nov 09, 2008 | Canon PIXMA MP830 All-In-One InkJet...

4 Answers

Error 5400


the 5400 error is telling you there was excessive temperature in the printhead, and this error code will stop all printing attempts.

Unplug the power from the printer and leave it off for a hour and then check the pins inside the carriage and clean them and clean the contacts on the back of the head.

May 31, 2008 | Canon PIXMA MP150 All-In-One InkJet...

1 Answer

Canon MP530


it may need to be reset or the worse the power surge blew out its memmory chips inside the printer. printers come with an amount of memmory about 4 to 8 megs so that it can remember print jobs try a test page after you leave unpluged for half hour
the printer should be able reset itself

May 04, 2008 | Canon PIXMA® MP530 All-In-One Printer

3 Answers

Canon MP 600 Will Not Turn On .... grumble.


I had this same issue. Lost power in the house for just a second, but after the printer would not turn on. I think that the loss of power caused the printer to get stuck in a locked state. Tried everything I could think of including changing outlets that the printer was plugged into but nothing seemed to work. Saw a troubleshooting tip on the Canon webpage about unplugging the unit for 5 minutes and thought it was hooey, but tried it anyway. Ended up leaving the unit unplugged for probably 15 minutes and when I re-plugged it in it fired right up.

Oct 09, 2007 | Canon PIXMA MP600 all-In-One InkJet...

Not finding what you are looking for?
Canon PIXMA MP830 All-In-One InkJet Printer Logo

Related Topics:

184 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Printers & Copiers Experts

kakima

Level 3 Expert

96467 Answers

old marine
old marine

Level 3 Expert

1463 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Canon Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...