Question about Siemens PC Desktops

1 Answer

Turn on computer can't get out of the safe mode screen the computer will not boot up in any mode

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 36 Answers

Hi you can try this , Restart the computer.
At the first startup screens, press the F8 key repeatedly until the Windows Startup Menu appears.
Select Normal Startup.
If the computer still starts in safe mode, go to the next step.

  1. Disconnect all peripherals attached to the computer.
  2. Restart the computer twice.
    1. If Windows does not start in safe mode, re-attach one peripheral at a time until you find the peripheral that is causing the problem. Refer to the peripheral's support to see if there are any known issues and resolutions for this problem.
    2. If Windows still starts in safe mode, disconnect any recently added hardware as explained in the following section.
    3. Turn the PC off, wait about ten seconds, and then turn the computer on.
    4. Press the F1 key repeatedly during the first logo screen (This keypress may be different on some computer models).
    5. Press the F5 key and then press the Enter key to set the setup defaults.
    6. Press the F10 key and then press Enter to save the settings and exit.
    7. try system restore and restart the system
    8. Click Start , Run , and type the following into the Open field: msconfig
    9. Click the Boot.ini tab.
    10. Remove the checkmark next to /Safeboot , if it is selected.
    11. Click OK and restart the PC.

Posted on May 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Grey screen


Please, try this test:

When you turn on the computer, press the F8 key multiple times to get to a menu (recovery, safe mode). If you get there, select Safe Mode. Once on Safe mode, restart the computer to see if it ever gets to normal boot.

Mar 19, 2013 | Acer PC Desktops

1 Answer

Desktop screen


try booting in safe mode and see if the screen displays properly.

Turn off the computer, then hit the power button to turn it back on and immediately start hitting the F8 key repeatedly until you see SAFE MODE. Take the Safe Mode option and let it boot up. Safe Mode will look different to you, the screen will be darker and the icons bigger, this is normal.



Try connecting another monitor to the computer. Borrow a monitor from a neighbor, friend, relative or co-worker and connect it to the computer. If the Borrowed monitor shows the 1 inch black space then your video card might be going bad or you might have a virus infection. If the Borrowed monitor displays ok then your original monitor is bad.

May 29, 2012 | Dell Inspiron 530 Desktop Computer...

1 Answer

Hp slimline s3000 goes immediately into sleep mode


Try booting into Safe Mode then go into the Control Panel and change the Power Options.

Turn off the computer, then hit the power button to turn itback on and immediately start hitting the F8 key repeatedly until you see SAFEMODE. Take the Safe Mode option and let it boot up. Safe Mode will lookdifferent to you, the screen will be darker and the icons bigger, this isnormal.Once safe mode is up click Start/Control Panel and look for Power Options.

Apr 08, 2012 | PC Desktops

3 Answers

Wont boot in safe mode


start your laptop before booting windows press f8 button continuously

ndows 2000 / XP users

bulb.gif If you are running Safe Mode because you cannot get into Windows, you may want to first try loading the last known good configuration.

To get into the Windows 2000 / XP Safe mode, as the computer is booting press and hold your "F8 Key" which should bring up the "Windows Advanced Options Menu" as shown below. Use your arrow keys to move to "Safe Mode" and press your Enter key.

Note: With some computers, if you press and hold a key as the computer is booting you will get a stuck key message. If this occurs, instead of pressing and holding the "F8 key", tap the "F8 key" continuously until you get the startup menu.

Trouble Getting into Windows 2000 or Windows XP Safe mode - If after several attempts you are unable to get into Windows 2000 or Windows XP Safe Mode as the computer is booting into Windows, turn off your computer. When the computer is turned on the next time Windows should notice that the computer did not successfully boot and give you the Safe Mode screen.

Windows Advanced Options Menu
Please select an option:

Safe Mode
Safe Mode with Networking
Safe Mode with Command Prompt

Enable Boot Logging
Enable VGA mode
Last Known Good Configuration (your most recent settings that worked)
Directory Services Restore Mode (Windows domain controllers only)
Debugging Mode

Start Windows Normally
Reboot
Return to OS Choices Menu

Use the up and down arrow keys to move the highlight to your choice.

Once you're done in Safe mode if you want to get back into Normal Windows restart the computer like you normally would and let it boot normally. Click here to get additional information about getting out of Safe mode.

Microsoft Windows Vista and Windows 7 users

bulb.gif If you are running Safe Mode because you cannot get into Windows, you may want to first try loading the last known good configuration.

To get into the Windows Vista and Windows 7 Safe Mode, as the computer is booting press and hold your "F8 Key" which should bring up the "Windows Advanced Options Menu" as shown below. Use your arrow keys to move to "Safe Mode" and press your Enter key.

Note: With some computers if you press and hold a key as the computer is booting you will get a stuck key message. If this occurs, instead of pressing and holding the "F8 key", tap the "F8 key" continuously until you get the startup menu.

Trouble Getting into Safe mode - If after several attempts you are unable to get into Safe Mode as the computer is booting into Windows, turn off your computer. When the computer is turned on the next time Windows should notice that the computer did not successfully boot and give you the Safe Mode screen.

Sep 27, 2011 | Lenovo G460 Laptop Computer - 06779XU...

1 Answer

Blue Screen Error driver_irql_not_less_or_equal 0xd1 Caused by xavzts.sys


You might have installed incompatible drivers. Boot the computer into "Safe Mode" by pressing and holding down the F8 right after pressing the power button to turn PC on. Select "Safe Mode" in the Windows Advanced Boot Options". Icons might look bigger or the screen will look different in Safe Mode. Click Start>All Programs>Accessories>System Tools>System Restore. Use System Restore to restore the computer back to a date when the computer is working fine. The computer will restart during the process.

Hope this help. Goodluck!

Mar 26, 2011 | PC Desktops

3 Answers

How do you put windows into safe mode?


Power on or Restart your computer, keep tapping F8 on the keyboard while it boots up. After few seconds, you'll be taken to the "Advanced Boot Options" with "Safe Mode" in the lists. Use the Up-Down arrow keys to highlight the "Safe Mode" and press enter on the keyboard to confirm the selected boot options. Black Screen with white texts will be displayed on the display, wait for few seconds until you see the windows logon Screen. You'll also see a confirmation message box asking you to confirm to boot into Safe Mode, click "yes" or "Ok" and proceed forward. There now you are in the Safe Mode.

If you need further help, let me know.

Good luck.

Thanks for using FixYa.

Sep 26, 2010 | PC Desktops

3 Answers

How do I put my HP computer in safe mode.


Just after post(the computer boots up) and just before you see windows booting press F8, it will bring up a blck page with different selection options to boot your pc, use the arrow keys to go to the top of the page where it says safe mode and hit enter,, the computer should now boot to windows in save mode. hope this helps.

Sep 23, 2010 | PC Desktops

3 Answers

Frozen cursor


do you have a wired or wireless mouse?
Have you tried attaching a different mouse to your computer?
What is the brand name of your mouse?

Try booting your computer in Safe Mode. To do this, after turning on the computer, press F8 button several times. You will see a screen that will ask you to boot normally, boot in Safe Mode or boot in Safe Mode with Network Connections. Select Safe Mode.

See if your mouse works then.

Check back with me for further help, if needed. There are additional things you could try.

Oct 08, 2009 | E-Machines eMachines Desktop PC

1 Answer

Gateway desktop 700xl computer stops at the logo screen and stops


I presume that your logo screen reads 'windows xp'. If so, there might be a problem with one of your startup drivers. Try to boot the computer in safe mode and uninstall any recently installed hardware or software and try to boot it up. It may be a virus also. So update your antivirus and run a complete scan. To boot in safe mode, hold F8 key when you're switching on your computer. you should see a screen which would give you the boot up options. Select "Safe mode with networking". This option lets you browse the internet from safe mode in case you need to.

Regards

Mar 16, 2009 | PC Desktops

1 Answer

Changed screen resolution. Now when turning on computer and monitor a message appears " is screen resolution correct? If any key is touched the monitor goes to standby.


try to boot on safe mode, by pressing f8 while booting then choose safe mode,

while in safe mode you can set the resolution back to its default .

Sep 11, 2008 | PC Desktops

Not finding what you are looking for?
PC Desktops Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Siemens PC Desktops Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

rclarke250

Level 1 Expert

8 Answers

Reprep

Level 2 Expert

142 Answers

Are you a Siemens PC Desktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...