Question about Earthquake Sound PH-D2 Car Audio Amplifier

1 Answer

HIFONICS XXV THOR

NEED PREAMP BOARD DWM3640NHV_V30
email bonitofirebird@hotmail.com

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 631 Answers

Why don't you repair the one you have?

Posted on May 20, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Im looking for a company that sales hifonics samson xi line input that broke of my amp..


Hifonics is sold by Maxxsonics

http://www.maxxsonics.com/hifonics/

You can contact them at support@maxxsonics.com

Feb 28, 2011 | Hifonics Generation XI Thor Car Audio...

1 Answer

How to set gains, brand new amps dont kno much about car audio.. how do i tune my amp for loud bass


for loud bass is 120Hz the freq. and adjust the audio gain in scale 1 to 10 in 7.

Apr 24, 2010 | Hifonics XXV Sampson Car Amp

1 Answer

I hook it up and the diag light comes on


yes you have a internal fault of the amp. the circuit that puts it into safe mode is bad and that is a very small chip on the board know as a op amp. needs to be repaired.

Jan 29, 2010 | Hifonics Generation XI Thor Car Audio...

1 Answer

Bxi 2006 audio driver board need to replace


If the output transistors are not shorted, he's probably correct in suspecting the driver board but it can typically be repaired. Have him email me and I'll send him a photo showing the two that most commonly fail.

babin_perry at yahoo.com

Nov 21, 2009 | Hifonics Brutus BX 1205D Car Audio...

1 Answer

I have a 2000 watt hifonics brutus amp ...it worked fine but 1 day it just stopped working..the power light doest light up but the hifonics led lights are still on...whats the problem?


there is a step up converter inside the amp that likes to come loose from the board. This may be your problem. Otherwise Check all the chips for burns or disconnect

Nov 13, 2009 | Hifonics Brutus BX 2005D Car Audio...

1 Answer

The hifonics amp is on but the subs dont work


pull your subs out of your box and test each sub with a 9 volt battery it should **** in if postive is to negative and extend if matched neg to neg pos to pos

Nov 01, 2009 | Car Audio & Video

1 Answer

I hook the hifonic amp up and it cuts on but the subs dont beat but the subs work


Try switching around one of the pos/neg speaker wires (you may have one crossed and they are firing out of phase, meaning when one pushes out the other pushes in and vise versa causing the base signals to cancel each other out) while the system is playing, only switch one speaker,not both. You can normally look at the subs and tell if they are moving very good and not much bass is there, you could also have the wrong box for them, this will also give a similar result

Nov 01, 2009 | Hifonics Generation XI Thor Car Audio...

1 Answer

I have a Hifonics XXV Colossous and 2 JL 500/1's. I want to know which I should use to push my 2 12" W7's to get my full money's worth and the best of the subs. Also if someone can describe how I should...


i highly recomend you use the hifonics colossous and wire the subs @ 2 ohms and you would be right about nominal power handling for the W7 which is rated @ 1000W, and your amp would push about 1100W to it. just be carefull when adjusting. and the best advice i can give you on the settings is as follows: Turn up the volume to the desired listening average level. (what you would normally have it on when driving) then adjust your amp by turning the different controls up, and then back down a 1/4 turn after distortion occurs. in your case with so much power dont turn them up all the way right away ease into it be gradual listen to the change in the sound.

Mar 04, 2009 | Jl Audio 1000/1 Car Audio Amplifier

1 Answer

Gets very hot and do not turn on


SOUNDS LIKE YOU BURNT UP THE POWER OUTPUTS IT'S UP TO YOU WEATHER YOU WANT TO BRING IT TO A REPAIR PLACE
IT MAY COST ALOT TO FIX GOOD LUCK

Jan 10, 2009 | Hifonics Generation XI Thor Car Audio...

1 Answer

Overheating


The Kicker 10 may be running a 1 ohm load and that amp isn't 1 ohm stable.

Sep 08, 2006 | Hifonics Generation XI Thor Car Audio...

Not finding what you are looking for?
Earthquake Sound PH-D2 Car Audio Amplifier Logo

Related Topics:

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Earthquake Sound Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4724 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

yadayada
yadayada

Level 3 Expert

64052 Answers

Are you an Earthquake Sound Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...