Question about Remington Polesaw Wizard

1 Answer

No response at all - Remington Polesaw Wizard

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 211 Answers

Hi

Remove the spark plug and checkthe spark.Then check the compression.Priming the engine(put small gas on the sparkplug hole) Put back the spark plug and try to start the engine.Let me know what happens.

cheers savumihai71

.

Posted on Dec 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to know which way to turn screw right or left to ad more oil onto chain and bar


the right is less oil
and the Left is more oil
to be sure ask a dealer a good one give you a response
if it not give you a response ask a another dealer !

Aug 27, 2014 | Chainsaws

1 Answer

Show way to turn oiler for chain


the right is less oil
and the Left is more oil
to be sure ask a dealer a good one give you a response
if it not give you a response ask a another dealer !

Aug 27, 2014 | Echo Model Cs 315 Cs315 Cs-315 Chain Saw...

1 Answer

Poulan 45cc chainsaw will start running with starting with choke, but will not stay running.


Sounds like the low speed fuel adjustment is out of whack....you can reset it by turning it in all the way clockwise...then as a starting point, turn it out 1 and 1/2 times, start the engine and slowly adjust the screw until the engine starts to choke out..when this occurs, turn it back in until it starts to choke again...then you need to set it somewhere in between to find the "happy medium"....thew high speed screw is adjusted after you get the engine idling properly...if you haven't messed with this then I wouldn't worry about it..unless you have poor high speed operation, then you will need to set the high speed screw...the object here is to obtain the best low to high speed throttle...if , when you throttle up the saw, the engine bogs or goes to high speed slowly , here is where you adjust to get the best throttle response...use small increments until you achieve the desired response

Apr 26, 2011 | Poulan Chainsaws

1 Answer

Onan performer p220 ohv will run fine then get very rough at high speed and idle. Has new fuel pump, all hoses are new and tight, and new fuel filter. Would appreciate ideas on what to check next


there should be 2 screw controls labeled "H" and "L"...these are the carb adjustments for low speed and high speed...you may need to adjust them to get the best possible response between low and high throttle performance...you only need to get it started and then slowly turn the "L" control until it idles smoothly..then move on to the "H" control and while going from low idle to high with the throttle trigger adjust it slowly until you get a good, smooth response from low to high

Jan 23, 2011 | Chainsaws

1 Answer

Hi, It has been weeks since I first wrote to you. I trust my response to your mails were within 24hrs when you asked for details of the defective product, hoping that the issue could be resolved at the...


Let me know what you have going on.It is listed under chainsaws but you mention scrapbook so I assume there is no appropriate category for you(no surprise there).I work with many people out of the USA.Although,if you are in AU or NZ,it may take a couple times because you are in the afternoon and I am up past bedtime :( Let me know.Greg Scotland person 2 days ago.I answer many more free questions than I do paid for ones because I initially started to help people in your situation.Money is sort of a bonus but from what I make,far from any job.More to come later.

Oct 30, 2010 | Chainsaws

1 Answer

I have the at&t house phones there is four of them and I'm trying to find out a way to put a privacy mode on them, so no one else in the house can hear someone else's conversation.


No response to 2 clarification requests.
No response to flagging as not chainsaw with request it be moved to correct category.
This is NOT a chainsaw

delete/close

Oct 19, 2009 | Homelite Consumer Products 9.0 Amp, 14 In....

1 Answer

Directions for reconnecting gas lines


Clarification Request
Posted by dontbother10 on Sep 16, 2009
We need the make, model, and serial numbers from the manufacturer?s tag to help you farther.

No response - please close

Jul 07, 2009 | Ryobi Factory Reconditioned 18" 40cc...

1 Answer

Putting a new chain on mac cat super 16 av, and adjust more oil


Delete this item. We have requested numerous requests for clarification with no response.

Apr 10, 2009 | McCulloch Chainsaws

1 Answer

Homelite 240 chain saw will start & run for about 2 min then when


Delete this; no response to clarification since Feb.

Feb 22, 2009 | Homelite Chainsaws

Not finding what you are looking for?
Remington Polesaw Wizard Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Remington Chainsaws Experts

Roland W VanLue
Roland W VanLue

Level 3 Expert

375 Answers

EugenesDIYDen
EugenesDIYDen

Level 3 Expert

479 Answers

Phil Walker
Phil Walker

Level 3 Expert

602 Answers

Are you a Remington Chainsaw Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...