Question about Computers & Internet

2 Answers

How to install eMachines N-10 memory model W340UA

Posted by on

  • christine reardon
    christine reardon Oct 07, 2008

    Thanks that did the trick,

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Flip the unit ove on the bottom you will see a two covers. the one cloest to you headphone jacks is the one you want. use a small philps screwdriver to remove the cover.
there is one 512MB 400MHz DDR2-400, PC2-3200, 200p SODIMM, 1.8v, CL=3, 64Megx64 memory unit from the factory if you are just upgrading to 1GB the buy a 2nd SODIMM and put it in the slot that is hiden behind the cover and reinstall the cover and restart the unit and enjoy. BUT if you want more than 1 GB I would pull the 612 and install 1 2gb or 2 1gb SODIMM uints.
Limit of 2GB on a N-10

Posted on Oct 06, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 221 Answers

User Manual will help you.






Posted on May 20, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install 4 gig ram on EMachine 3611


You cannot. See table below.
eMachines W3611 RAM Specifications
Standard Memory 512 MB (removable) Maximum Memory 2.0 GB Memory Expansion 2 sockets Memory Comments PC2-4200 DDR2 SDRAM DIMMs. Supports Dual Channel DDR2. CPU Type 3.0GHz Intel Pentium 4 631 Model Comments 800MHz FSB, Intel 945G Chipset

Jun 09, 2014 | Computers & Internet

1 Answer

I want upgrade my emachines t6528 hard drive and ram.i need help


Memory Upgrade for eMachines eMachines T6528 Computer, the eMachines eMachines T6528 Computer takes the PC3200 DDR SDRAM DIMMs. Supports Dual Channel DDR. Memory Type, and comes installed with 512 MB (removable) of Memory. You can upgrade your eMachines eMachines T6528 Computer to up to a maximum of 4.0 GB Memory, the system has 4 sockets to install Memory, already with 512 MB (removable) standard Memory installed. For best Computer performance use the maximum amount of allowed Memory per slot for your Computer.


As for the Hard Disc.... the following address will give step by step instructions on installing a new HD. http://www.manualowl.com/m/eMachines/T6528/Manual/

Thank You for using FixYa
Tom Miller
KD4DTK

Aug 19, 2012 | E-Machines T6528 PC Desktop

1 Answer

Display screen don't light up but you can see it with a flashlight [emachines model w340ua] .


Either invertor board or the lamp is faulty, so your backlight is not working. Both of those problems require some skill with electronics and soldering. The system is thus repairable, but i am not sure if it is an economically viable option. If you are using it as a desktop replacement, connecting an external monitor, if you have one, will make the system usable again.

Feb 21, 2011 | Computers & Internet

1 Answer

Gateway Laptop W340UA black screen


  1. take out the memory
  2. turn on again without memory (you should hear long beep sound) and turn it off again
  3. clean memory using eraser (better if you have spare memory to replace it)
  4. now try again
  5. if not working, checks whether the work properly? and clean the fan from dust. and try to switch it on again.
I look forward to hearing further.

Dec 14, 2009 | Gateway Computers & Internet

1 Answer

How to install memory for T3642 eMachine


eMachines T3642 Computer takes the PC2-5300 DDR2 SDRAM DIMMs. Supports Dual Channel DDR2. Memory Type, and comes installed with 1.0 GB = 512 MB (removable) + 512 MB (removable) of Memory. You can upgrade your eMachines eMachines T3642 Computer to up to a maximum of 2.0 GB Memory, the system has 2 sockets to install Memory, already with 1.0 GB = 512 MB (removable) + 512 MB (removable) standard Memory installed. For best Computer performance use the maximum amount of allowed Memory per slot for your Computer.


INSTALLATION PROCEDURE
1. Place the computer power switch in the "off " position and disconnect the AC power cord.
2. Remove the computer top cover following the instructions in the model-specific owner manual.
3. Before touching any electronic components, make sure you first touch an unpainted, grounded metal object to discharge any static electricity stored on your clothing or body.
4. Locate the memory expansion sockets on the computer motherboard. If all the sockets are full, remove smaller capacity modules to allow room for higher capacity modules.
5. The ejector tabs shown in the illustration are used to remove a module. By pushing outward on the ejector tabs, the module will pop-up from the socket and it can then be removed.
6. Handle your new module carefully; do not flex or bend the module. Always grasp the module by its edges.
7. For most installations, DDR modules can be installed in any available expansion slot. Other installations may require the memory to be installed in a particular sequence based on the modules capacity. Check your owner manual to determine the correct installation sequence for your configuration.
  • Insert the module into an available expansion socket. Note how the module is keyed to the socket. This ensures the module can be plugged into the socket one way only. Firmly press the module into position, making certain the module is completely seated in the socket. The ejector tabs at each end of the socket will automatically snap into the locked position. Repeat this procedure for any additional modules you are installing. install_ddr.gif 8. Once the module or modules have been installed, the computer top cover can be reinstalled.
    9. Plug in the AC power cord and reinstall any cables disconnected during the installation process.
    10. Turn on the computer and follow the instructions in your computer owner manual that describe the steps necessary to allow your computer to recognize the newly installed memory.
  • Oct 23, 2009 | E-Machines eMachines T3830 PC Desktop

    1 Answer

    Dual Channel on an Emachines T5082


    Look closely at the BOLD print

    Memory Upgrade for eMachines eMachines T5082 Computer, the eMachines eMachines T5082 Computer takes the PC2-4200 DDR2 SDRAM DIMMs. Supports Dual Channel DDR2. Memory Type, and comes installed with 512 MB (removable) of Memory. You can upgrade your eMachines eMachines T5082 Computer to up to a maximum of 2.0 GB Memory, the system has 2 sockets to install Memory, already with 512 MB (removable) standard Memory installed. For best Computer performance use the maximum amount of allowed Memory per slot for your Computer.
    Choose the following Memory Upgrade for eMachines eMachines T5082 Computer.

    Apr 17, 2009 | E-Machines T5082 PC Desktop

    2 Answers

    Black screen


    - I had the exact same problem with a eMachines W340UA and other machines. I'm not sure what this does, but I resolved it by booting into Safe-Mode. Upon successful boot into Safe-Mode (without Networking), I restarted the computer in the normal mode and it for then after worked. Please try this; though I can make no logical statement as to what occurrs or what gets fixed, I have had this method work on several machines.

    INSTRUCTIONS:
    Fire up the machine, after BIOS postings, continually press the F8 key. From the list of startup options, choose "Safe Mode (Without Networking). It should boot up in this mode.
    After the successful boot, restart the machine and allow it to boot in normal mode. If all goes as it has for me, you will successfuly boot into Windows.
    -----------------------------------------------------------------------------------------
    P.S: If anyone knows where the coin battery is on an eMachines w340ua laptop, and hot to get to it, please let me know. Thank you and I hope this helps!

    Sincerely;
    Glenn T. Kitchen
    admin@consultingVisions.com

    Oct 16, 2008 | Computers & Internet

    Not finding what you are looking for?
    Computers & Internet Logo

    Related Topics:

    399 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Computers & Internet Experts

    Brian Sullivan
    Brian Sullivan

    Level 3 Expert

    27725 Answers

    kakima

    Level 3 Expert

    101711 Answers

    David Payne
    David Payne

    Level 3 Expert

    14160 Answers

    Are you a Computer and Internet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...