Question about Kenmore Elite HE4 Electric Dryer

1 Answer

Kenmore elite E1 Code

Model number 110.61066000 kenmore elite.

Posted by on

  • mlcoletta May 27, 2008

    My dryer is not heating properly so after I go down and check the clothes I will start the dryer again.... Next time I go down it will be flashing an Error code of E1... anyone knows what this means???

  • eschindlr Jun 30, 2008

    I'm getting the same code on my HE3 dryer. It runs but only for a short time before it quits and gives me the code.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 91 Answers

E1 stands for thermistor open or closed repl. will fix problem

Posted on Jan 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is an E1 error code? what does it mean?


Go to google and ask what does E1 error code mean on a Kenmore Dryer (Model #) and you will get several answers

Jul 29, 2015 | Kenmore Elite HE4 Electric Dryer

1 Answer

The dryer shuts off, keep getting an E1 code, what needs to be done


It sounds like this is a Whirlpool Duet or a Kenmore Elite Dryer due to the error code E1 being available only on this models. The problem here is an open thermistor as what error code E1 means. It's either the thermistor is exhibits an extremely high resistance or the wire harness connecting it to the control board is broken or cut open. Click on the link below for the detailed procedure in accessing the thermistor.

Whirlpool Duet and Kenmore Elite Electric Dryers Not Starting


Measure the resistance of the thermistor and refer the table below. Normal thermistor resistance is around 10000 ohms (10K) at room temperature.

jahn27_560.jpg


Replace the thermistor if the resistance is significantly higher (or lower) than what it is supposed to be based on the resistance table above. Check the wire harness connecting it to the control board, if the resistance turns out good, and make sure the connectors are good and the wires are intact. Replace the wire harness if necessary. Consider replacing the control board if both the thermistor and the wire harness turn out good. The link below might enlighten you further on the troubleshooting of the thermistor.

Thermistor Troubleshooting on Whirlpool Duet and Kenmore Elite Dryers

Aug 21, 2011 | Dryers

1 Answer

E1 error


The fault code E1 means the electronic control detected the thermistor is open. It's either the wire harness connecting the thermistor and electronic control is broken or the connection is loose or the thermistor is indeed open. Measure the resistance of the thermistor then refer to the temperature and resistance table for the normal thermistor resistance values. Click on the link below for the detailed troubleshooting procedure.

Troubleshooting Error Code E1 on Kenmore Elite and Whirlpool Duet Dryers

Dec 31, 2010 | Kenmore Elite HE3 Steam 8676 Dryer

1 Answer

Code E1 on Kenmore dryer


The electronic control detected the thermistor is open. It's either the wire harness connecting the thermistor and electronic control is broken or the connection is loose or the thermistor is indeed open. Measure the resistance of the thermistor then if it reads open or the harness of broken. Refer to the detailed troubleshooting of this error code in the link provided below.

Troubleshooting of Error Code E1 on Kenmore Elite and Whirlpool Duet Dryers

Oct 08, 2010 | Kenmore Elite HE4 Electric Dryer

2 Answers

Code E1 comes up and dryer quits operation


If the first 3 numbers of the model number are 106, 110, 198, 562, 665; then the E1 code means thermistor failure.

You can replace this component yourself.

May 03, 2009 | Kenmore Elite HE4 Electric Dryer

1 Answer

My dryer stops in mid cycle and gives me an error code of E1


It is a bad thermistor on the blower housing

http://forum.appliancepartspros.com/dryer-repair/1379-kenmore-elite-e1-sensor.html


Apr 18, 2009 | Kenmore Elite Oasis 6808 Electric Dryer

1 Answer

Error Code E1


replace the thermistor

Dec 20, 2008 | Kenmore Elite HE4 Electric Dryer

1 Answer

I constantly got E1 Error code on my Kenmore Elite H3 GAS dryer


E1 error code indicates an open thermistor or open thermistor circuit. A thermistor is a component that relays the temperature in the dryer to the control board. If the thermistor has failed, Error code E1 will be displayed.
You need to call a repair person to fix it.

Dec 18, 2008 | Kenmore Elite HE4 Electric Dryer

1 Answer

Kenmore elite


Hi! Puddrikko
I hope I can help you, I just need to make shure I am checking the correct Model Error code. If your first three numbers of the model number is 110 this may be a Thermistor Failure. If you have any more information let me now, I will try and help you.

Aug 08, 2008 | Kenmore Elite HE4 Electric Dryer

Not finding what you are looking for?
Kenmore Elite HE4 Electric Dryer Logo

Related Topics:

463 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Tim Whalen

Level 3 Expert

3056 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you a Kenmore Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...