Question about Jenn-Air JGR8855BDS Gas Kitchen Range

Open Question

Timer Function Stuck

Display shows "Timer 1 End" with the "1" flashing.
Cancel button does not get rid of the message.
Timer 1 on/off, Timer 2 on/off, and Setup button all not responding.

Posted by on

2 Suggested Answers

  • 278 Answers

SOURCE: My whirlpool duet washer has stopped mid cycle and

Sounds like the timmer in the control module has frozen and will not advance. It's one module for the whole display. I sometimes tap the module with a plastic screwdriver witch may releace it but it will do it again. I sorry to say but it's time for a repair man. I do't have the writing space to tell the procedure (if it is the problem) - Sorry, not good news

Posted on Oct 16, 2009

Daniel S
  • 4323 Answers

SOURCE: key do not work #'s 1 & 2, Lower bake , broil,

Hi

You'll need to check the oven temperature sensor and the contacts on the power relay board (PRB). You'll need a multimeter to check the resistance of the temperature sensor, multimeter would read between 1140-1150 ohms. If you notice any deviation in the reading then you'll need to replace the temperature sensor. Hope this helps... Please post back with model # if you need more information.

Daniel

Posted on Nov 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I to set clock on Sanyo Microwave EM-C678


1. Open door
2. Press clock/Kitchen Timer button the display will show "0:00" with the hour"0" flashing.
3. Enter the correct hour by turning the potary dial. Enter 1-12
4. Press clock/Kitchen Timer button the display will show "0:00" with the minutes "00" flashing.
5. Enter the correct minutes by turning the potary dial. Enter 00-59
6. Press clock/Kitchen Timer. The colon will remain flashing.
7. Close the door.

Sep 03, 2014 | Microwave Ovens

1 Answer

Set clock and be able to tell am from pm setting


The Clock uses a 12-hour cycle with a.m. and p.m.
1. Check that the oven is off.
2. Press CLOCK.
3. Press TEMP/TIME "+" or "-" arrow pads to set the time of day, including a.m. or p.m.
4. Press CLOCK or START
The Timer can be set in hours or minutes up to 12 hours and 59 minutes.

1. Press TIMER.
2. Press TEMP/TIME "+" or "-" arrow pads to set the length of time.
3. Press START to begin the countdown. If enabled, end-of-cycle tones will sound at end of countdown.
4. Press TIMER twice to cancel the Timer. Do not press the CANCEL/OFF keypad because the oven will turn off.
5. If the TIMER is running, but not in the display, press TIMER to display the countdown for 5 seconds

Delay Start:
The Start Time keypad is used to enter the starting time for an oven function with a delayed start.

Hope this answers all you questions about your stove.

Jaye

Nov 04, 2013 | Whirlpool RF263LXTQ Range

2 Answers

The link on FixYa to the HB65R Intermatic timer Manual seems to be broken. Do you still have it?


Fixya does not have HB65 manual posted.
Open following link to identify timer and download manual in English.
If this is not your timer, add a comment with clear description of timer, or in-focus photo of timer posted on flicker, so I can locate possible manual.
http://waterheatertimer.org/Intermatic-timers-and-manuals.html#HB65R
http://waterheatertimer.org/Woods-timers-and-manuals.html#N1506

Jul 19, 2011 | Garden

2 Answers

I need instructions on how to program my intermatic timer 1076311. It's a two button timer.


The Intermatic outdoor timer 1076311 is Intermatic model HB65R.
It has two buttons, TIME and MODE and a digital display.
Instructions:
1. Plug in the timer, which self-tests. If error, EE flashes.
If normal, 88 flashes for 3 seconds, then display shows C and you can proceed to set the timer.
2. Push the TIME button to set C (current time) AM hours 1-12 and PM hours 1. to 12. (Example: for 7 AM push the TIME button until the display shows "7" for 7 PM push the TIME button until the display shows "7."
3. Now push and hold down the MODE button until the display shows P for the "ON time."
4. Push the TIME button to set the hour to turn ON, from AM 1 to 12 or PM 1. to 12.(Example: if you want the power on at 7 PM repeatedly push the TIME button till the display reads 7.)
5. Push and hold down the MODE button until the display reads E for "END time" (time you want the power OFF)
6. Push the TIME button repeatedly to set the end time hour from AM 1 to 12 or PM 1. to 12. The time off will display.
7. Press the MODE button to toggle between ON and the current time.

If you unplug the timer you will have to reset the C (current time), P (ON time) and E (END or OFF time).

Dec 20, 2010 | Solar Intermatic Timer 6 Outlet Outdoor

1 Answer

How do I program a Noma N1506 timer?


All Woods timers and manuals
ttp://waterheatertimer.org/Woods-timers-and-manuals.html

N1506 manual:
http://waterheatertimer.org/pdf/Woods-49122-N1506-manual.pdf

N1506 is heavy duty outdoor timer with display screen.
Plug timer in and display flashes C.
Set current time: press Time button once and display shows 1 am
Keep pressing time button until current time with am pm displays.
Dot in lower right corner corresponds to pm hours.

To set timer program:
Press Mode button, display flashes P
Press Time button until desired ON time displays.
Press Mode button again and display flashes E
Press Time button until desired OFF time displays
When programming is finished, press Mode button and display shows current time.

To reset timer, unplug timer for 10 seconds and re-program timer.
Timer must be reset after power outage. Display will warn by flashing C.

Plug lights into timer.
If lights have a switch, switch must be on.
For manual override, press Mode button, and display shows O and lights will be ON until next program change.
To use timer function, press Mode button until current hour displays.

Dec 12, 2010 | Solar Noma 7 Day, 6 Event Outdoor Timer -...

1 Answer

How do I set the Woods N1506 timer?


N1505 timer manual:
http://waterheatertimer.org/pdf/Woods-49122-N1506-manual.pdf

N1506 is heavy duty outdoor timer with display screen.
Plug timer in and display flashes C.
Set current time: press Time button once and display shows 1 am
Keep pressing time button until current time with am pm displays.
Dot in lower right corner corresponds to pm hours.

To set timer program:
Press Mode button, display flashes P
Press Time button until desired ON time displays.
Press Mode button again and display flashes E
Press Time button until desired OFF time displays
When programming is finished, press Mode button and display shows current time.

To reset timer, unplug timer for 10 seconds and re-program timer.
Timer must be reset after power outage. Display will warn by flashing C.

Plug lights into timer.
If lights have a switch, switch must be on.

For manual override, press Mode button, and display shows O and lights will be ON until next program change.
To use timer function, press Mode button until current hour displays.

Dec 01, 2010 | Woods Outdoor Lighting Timer

1 Answer

Model N1506, I need Operation instructions for this Woods Light Timer?


N1505 timer manual:
http://waterheatertimer.org/pdf/Woods-49122-N1506-manual.pdf

N1506 is heavy duty outdoor timer with display screen.
Plug timer in and display flashes C.
Set current time: press Time button once and display shows 1 am
Keep pressing time button until current time with am pm displays.
Dot in lower right corner corresponds to pm hours.

To set timer program:
Press Mode button, display flashes P
Press Time button until desired ON time displays.
Press Mode button again and display flashes E
Press Time button until desired OFF time displays
When programming is finished, press Mode button and display shows current time.

To reset timer, unplug timer for 10 seconds and re-program timer.
Timer must be reset after power outage. Display will warn by flashing C.

Plug lights into timer.
If lights have a switch, switch must be on.
For manual override, press Mode button, and display shows O and lights will be ON until next program change.
To use timer function, press Mode button until current hour displays.

Dec 01, 2010 | Hardware & Accessories

1 Answer

Err68


Hi


Error E68 on Frigidaire dryer means that One of the keys (buttons) is stuck closed (active). Please check whether any button is pressed or stuck. Also try removing the lint filter and clean the contacts of the inside of the filter.
Try performing function test to check which button is at fault. Enter function test mode and perform key (button) test to determine which button is at fault. Carefully free the and perform the test again. If button is free but the key struck code still exists then you'll need to replace the electronic control.

Function Test--

1. Press and hold Select and Cancel buttons simultaneously for 6 seconds to reset the control. The buzzer will sound 1 time and “rES” will be shown briefly in the display.
2. Immediately after, rotate cycle selector knob 5 turns counter-clockwise to the second position from the bottom. Press and hold the Options and Cancel buttons simultaneously for 2 seconds. The control will enter test mode, the buzzer will sound 3 times and all LED’s will rapidly flash.
To EXIT test mode, press and hold the Select and Cancel buttons simultaneously for 6 seconds or disconnect power from dryer. Dryer will be reset for regular operation.

Please post back for any further assistance.

Daniel

Jul 21, 2010 | Frigidaire GLEQ2152ES Electric Dryer

6 Answers

My Whirlpool Duet Font Loader Washer stopped 1 minute before the end of the spin cycle; and I need to know how to reset it so that I can start another load of laundry.


Remove the front panelfbee677.jpg and check the pump filterd05d32e.jpg for objects8b65c4c.jpg then grab the tech sheet behind the white box and use the diagnostic instructions.
You have any non-HE soap in there or 2 much the machine will overamp and act all weird and then shut down with error code flashing. If it is an F-21 it means a Long drain. Possible cause: Clogged filter, clogged/failed pump.de495ab.jpg

May 25, 2010 | Washing Machines

2 Answers

Error:91:01 how do you get rid of it?


Hi,
Follow the procedures given below to have a perfect fix for your problem.
  • Press Menu button.

  • Toggle across from REC Mode to setup

  • Toggle down thrice from camera to setup 1

  • Toggle across into sub menu

  • Toggle down from four times to Initialize

  • Toggle across again to the sub-menu

  • Toggle up from cancel to OK

  • Press center button to accept the OK choice

  • Screen changes and so press okay again

  • It should restart the camera

  • Opening on the 'Clock Set' screen

Toggle down to cancel and use the camera and make sure that you have the camera to flash, if it works try again in the Auto function. If it is still not working dont worry follow the steps again two or three more times, As this is related to a software error message and not a hardware malfunction. If it is working then don't forget to set your Clock.

May 22, 2010 | Sony Cyber-shot DSC-W55 Digital Camera

Not finding what you are looking for?
Jenn-Air JGR8855BDS Gas Kitchen Range Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jenn-Air Kitchen Ranges Experts

Mike Carew

Level 3 Expert

969 Answers

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

 Fix Your Board
Fix Your Board

Level 3 Expert

310 Answers

Are you a Jenn-Air Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...