Question about Bakers Pride Y-600 Gas Single Oven

1 Answer

Thermostat setting for bakers pride y600 oven.

The screws worked loose behind the temperature knob on the thermostat and i dont know what to set them on.Can you advise?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 125 Answers

Hi, those screws are for the calibration of the knob to the thermostat, so your calibration is correct. Most likely you will have to contact a servicer to check the calibration, and set you knob and plate where they will align with the actual temp again.
Hope that helps, and thank you.

Posted on Jan 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Bakers pride y-600 oven . What is the best way for top door to be taken off ??


On the left side, remove the knobs and cover. The spring holding the door closed needs to be removed. Have someone hold the door closed while removing the door spring. Now let the door open and you will see two screws holding the door to the door rod assembly on the left side. These screws are usually 9/16. After removing the two screws, the door will pull off the door pin that is located on the right side.

Oct 24, 2013 | Bakers Pride Y-600 Gas Oven

1 Answer

Oven doesn't get to desired temp.


Hello there:
When the temperature is consistent but too high or too low, it could be one of several different things. First check to see if the thermostat sensing bulb has come loose from its holder. It could be lying on the floor of the oven or resting on the heating element. This would cause the oven to not heat correctly. If the thermostat bulb is not dislodged, it's likely that the thermostat or sensor is either mis-calibrated or defective. Electronic ovens with a digital display use a sensor to monitor oven temperature. To solve temperature problems for these models, you may need to replace the sensor. On some digital-display models, you can calibrate the temperature using the key pad. See your operator's manual for details. Ovens without a digital display often use a mechanical system for controlling temperature. On many of these units, you can remove the thermostat knob and adjust the knob itself to more accurately represent the actual setting of the thermostat. If, when you remove the knob, there's a screw on the back of it with a small calibration plate, you can loosen the screw, adjust the plate, then tighten the screw again. If the knob isn't adjustable, and the oven temperature is off by more than 30 to 40 degrees, you need to replace the thermostat to solve the problem.
Hope this is very helpful for you please feel free to rate this solution it helps our askers get the best possiable solutions from our fixya staff
best regards mike

Dec 26, 2010 | Ovens

1 Answer

How does the power level work in conjunction with the Thermostat? does the power goe through the Stat first or the power level.


Hello. These two areas within your oven operate on two separate systems because they operate on very different voltage needs and thus very different size wire. The thermostat is right behind the knob you use to set the oven baking temperature. There's a long, thin copper tube attached to this knob that leads into the oven compartment. It senses the temperature inside the oven and signals the thermostat to provide or prevent further heating. There's another type of thermostat--an electronic/mechanical hybrid unit--that has a small electronic circuit board behind the knob. It has a sensor attached to it--about the size of a 4- to 6-inch pencil, that protrudes into the oven. When the oven reaches the temperature you set, the sensor signals the circuit board, which turns off the electric burner(s) in the oven.

Jan 13, 2010 | Ovens

2 Answers

Baker's Pride P-44s P44s


You can get parts here at this link.

http://www.tmeinc.biz/xbpride.htm


Good luck and please rate

Sep 24, 2009 | Bakers Pride P-44S Oven

1 Answer

The Oven is set to 450 does not get above 280


  • When the food you're baking is done on top but not on the bottom--or when baking just takes far too long to finish--the bake element may be burned out.

    You may get fooled into thinking it's working, because the oven is hot inside. But many electric ovens use the broil element, too, during the preheat and bake cycles. So the food may be getting heated only by the broil element, which causes poor baking results.

    If the bake element is burned out, replacing it should solve the problem. Otherwise, you need to further troubleshoot the oven's electrical system to locate the defective wire or component.

  • When the temperature is consistent but too high or too low, it could be one of several different things. First check to see if the thermostat sensing bulb has come loose from its holder. It could be lying on the floor of the oven or resting on the heating element. This would cause the oven to not heat correctly.

    If the thermostat bulb is not dislodged, it's likely that the thermostat or sensor is either mis-calibrated or defective.

    Electronic ovens with a digital display use a sensor to monitor oven temperature. To solve temperature problems for these models, you may need to replace the sensor. On some digital-display models, you can calibrate the temperature using the key pad. See your operator's manual for details.

    Ovens without a digital display often use a mechanical system for controlling temperature. On many of these units, you can remove the thermostat knob and adjust the knob itself to more accurately represent the actual setting of the thermostat.

    If, when you remove the knob, there's a screw on the back of it with a small calibration plate, you can loosen the screw, adjust the plate, then tighten the screw again. If the knob isn't adjustable, and the oven temperature is off by more than 30 to 40 degrees, you need to replace the thermostat to solve the problem.
  • Aug 14, 2009 | GE Profile JT912 Electric Single Oven

    1 Answer

    Incorrect temperature


    under the oven knob is the screw that adjusts the temp. remove the knob and with a small blade screwdriver adjust the temp according to your wife's oven thermometer CW+hotter CCW=cooler
    then on the back of the knob is a screw to adjust the position of the knob with respect to the marker

    Apr 20, 2009 | Viking 30" Professional Select Built-in...

    1 Answer

    XL 44 Gas Range Oven temperature problem


    hi If the oven doesn't heat evenly or doesn't heat at all, the oven thermostat may be malfunctioning. First, determine how much the temperature in the oven is off from the control setting. To do this, put an oven thermometer on a center rack inside the oven and turn the oven on for about 20 minutes, with the thermostat set at any range between 300 degrees and 400 degrees Farenheit. If the oven thermometer reads 25 degrees or more lower or higher than the oven control setting, the thermostat should be recalibrated. Here's how to calibrate the thermostat:

    Step 1: Pull off the thermostat knob on the control panel. Behind the knob are two screws holding a round, notched plate. Loosen these screws, but do not remove them.

    Step 2: With a screwdriver, change the notch setting on the notched plate by turning the plate counterclockwise; for every eighth of a turn, the oven temperature goes up about 25 degrees Farenheit. To turn the heat down, turn the plate clockwise.

    Some thermostats can be adjusted by turning a screw inside the control knob shaft housing. To do so, remove the knob and insert a screwdriver into the shaft so that the screwdriver blade engages a screw slot. Turn the screwdriver counterclockwise about one-eighth of a turn to raise the heat about 
    25 degrees Farenheit. Here's how to test a malfunctioning thermostat:

    Step 1: Test the thermostat with a VOM (multimeter) set to the RX1 scale. The thermostat is located directly on the back of the control knob that regulates the heat. To gain access to the thermostat, remove the back service panel to the control panel.

    Step 2: Disconnect one electrical lead wire from a terminal of the thermostat and clip one probe of the VOM to each thermostat terminal. If the thermostat is in working order, the meter will register zero. If the needle jumps to a higher reading, the thermostat is faulty and should be replaced.

    Step 3: If necessary, replace the thermostat with a new one of the same type.

    If you need to replace the thermostat, follow these guidlines:

    Step 1: Disconnect the terminal wires to the thermostat and pull off the control knob.

    Step 2: Remove the retaining screws. On some ranges, there is a wire running from the thermostat into the oven. This wire operates a sensing bulb that controls the thermostat. The sensing bulb is usually held by a bracket; unscrew this bracket to remove the bulb. Then carefully slip out the wire, the bulb, and the thermostat.

    Step 3: Install the new thermostat using a reverse procedure.

    Nov 06, 2008 | Ovens

    1 Answer

    Too hot


    Hi, not sure if you ever received a reply, but there is a setting known as "bypass" on commercial thermostats, if you took the cover off to replace it, you can access this screw, it is part of the body of the thermostat, either to the left or the right of the knob shaft, usually has a "B" stamped, or molded into the body. What this setting does is when the thermostat reaches temperature, it would normally close, shutting off the supply to the burner, thus the temp would begin to fall, by the time it opened back up, the temp would have fallen too much, causing a large temp swing. The bypass setting opens or shuts a passage that "bypasses" the thermostat main valve, keeping just a little burner, making the swing, or fluctuation smaller. So, you probably have a setting too big, causing your bypass flame to be too big, raising, or keeping the temp too high, try turning it in (cw) to lower it slightly, a small turn makes a huge difference, so go easy. Hope that helps, and thank you.

    May 08, 2008 | Bakers Pride Y-600 Gas Single Oven

    2 Answers

    Door on my bakers pride y600 pizza oven


    Theses are called 3/4 door busings and should be changed when you replace the left side door rod (complete)and are available from any parts depot that sells bakers pride parts

    Jan 20, 2008 | Bakers Pride BAK-DS805 Gas Single Oven

    Not finding what you are looking for?
    Bakers Pride Y-600 Gas Single Oven Logo

    Related Topics:

    681 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Bakers Pride Ovens Experts

    paulcarew

    Level 3 Expert

    1875 Answers

    Dan Webster
    Dan Webster

    Level 3 Expert

    8147 Answers

     Fix Your Board
    Fix Your Board

    Level 3 Expert

    310 Answers

    Are you a Bakers Pride Oven Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...