Question about Fujitronic FH-778 Air Conditioner

Open Question

Fujitronic 4-1 just want to know where to put the water. if you can help, i will be glad.

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why my 2005 dodge durango keep over heating? I have put new turmastat, new clucth put it on the pressure hoses no leaks don't know what to do

My name Charles Lapinski and i am glad to help you with your problem today.

you might need to put coolant in the radiator.

Jan 17, 2015 | 2005 Dodge Durango Limited


So glad to found this website. Don't know if this is the same issue? But my...

This advice is for Kenmore Elite and Whirlpool Duet model FRONT LOADING washing machines. If you experience a problem where the washer does not drain properly or the drain pump makes excessive noise, here’s the information you need to check the drain pump:


  1. Unplug the washer while servicing inside the unit.
  2. Remove the lower kick panel under the door by removing the three 7mm screws under the bottom edge of the panel. HINT: Use a couple of blocks of wood to prop up the front feet of the washer to gain better access to the screws. Once the screws are removed the panel should drop down, and then pull off. If the panel becomes stuck, a slight tap on either side will dislodge it.
  3. Locate the drain pump. It will be located directly under the wash tub (it is the only pump this washer has).
  4. There is an access removal cover on the pump that can be removed to clean out the trap. BEFORE doing this, it is strongly recommended that you remove all residual water from the wash tub & drain line or you will have about a gallon or so inside your washer and on the floor to clean up.
  5. Here’s a helpful way of quickly removing the residual water. If you own a wet/dry shop vac, remove the drain hose from the standpipe at the wall and pull a vacuum with the shop vac. This will empty the wash tub, pump and drain lines. If you don’t own a shop vac, grab a bunch of old towels and open the access on the pump slowly so that it comes out at a trickle. Allow the towels to soak up the majority of the water. Close the access and stop the water if you need to get additional towels.
  6. Open the pump access and remove once you have all the water drained. Check the drain pump for foreign objects and debris. Check the pump impeller and make sure there’s nothing caught in it. Items as small as toothpicks or cotton swabs have been known to stop this pump from working.
  7. Clean out the pump thoroughly and reinstall the access cover. Make sure the cover is snug, but do not over tighten.
  8. Place the drain hose back in the standpipe (IMPORTANT – DO NOT FORGET!).
  9. With the bottom panel still off, plug the washer back in and select the following on the operator console – DRAIN SPIN, NO SPIN, and then press any button under OPTIONS 4 times (it must be the same button). “C00” will show on the console display as the washer begins diagnostics mode.
  10. Check the drain pump for leaks as the washer fills. The pump is gravity filled and will hold water even it is not pumping. Allow washer to run through diagnostics until it begins the wash tub tumble cycle.
  11. At this point, you can stop the diagnostics procedure by pressing PAUSE/CANCEL 2 times. The drain pump energizes and the washer will begin to drain.
  12. If the drain pump works normal and there are no leaks detected, reinstall the bottom panel and tighten screws.

NOTE: It is normal to have residual water left inside the wash tub under the wash basket. This is why it is important to leave the door ajar when not in use so this water does not become sour.

on Oct 29, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

Washer leaking water

Please be very careful, electricity and water don't mix. With that said try checking the hoses and make sure the hose clamps are secure. I have a Whirlpool washer and have had this problem among several other assorted problems. Glad I took out a service contract it more then paid for itself in the last two years.

good luck,


Jun 21, 2014 | Whirlpool Washing Machines

1 Answer

Drinking water dispenser inside my Maytag MFS2561 is dripping.

Hi Bud, welcome to FixYa. To address the water drip problem, I have 2 question's. Have you recently changed the water filter (or done anything else) and can you double check you have correctly posted the entire model number ? Let me know and I'll be glad to continue to help you from there.


Macmarkus :)

Nov 03, 2011 | Refrigerators

2 Answers

I have had my hamilton beach brew station for a year. The past 2 weeks, the water put in the bottom reservoir does not empty completely into the coffee reservoir. It leaves about 8 oz in the bottom water...

On your machine there is maybe inside water reservoir a hose or tube that goes down to bottom, or suppose to go down to bottom, to **** up all water. Look inside and see if hose is going all the way to bottom, maybe it got hung up or crooked. Please let me know, glad to help, thanks mike ( mr bean man )

Jun 08, 2011 | Hamilton Beach BrewStation 47214 Coffee...

1 Answer

Washer does not go through the spin cycle. "No

Does your machine drain water?

Usually before it goes to spin, the Electronic or Timer will first need to drain most water.
If it does not drain, clean the filter compartment (Found at the left bottom section of the door).

If it does drain water and I am wrong, please let me know, would be glad to help you.

Kind Regards

* If you found this solution helpful, please rate 4 thumbs up and leave a small testimonial. :-)

Apr 04, 2011 | Bosch WAS20160UC Front Load Washer

1 Answer

Water damage

Take battery out asap. The SIm card and sm card to. Put it into a bowl full of rice or bowl filled with silica gel. After a day put the battery back, power it on. If it works I am glad I have helped you if it doesn't work take it to the service

Mar 02, 2011 | Samsung SGH-A877 Impression Cell Phone

1 Answer


The water dispenser and ice maker solenoid comes as a set it is very possible the dispenser side for the water valve is defective. Get the model number of your refrigerator and click here=> sea_breeze_35.jpg and then enter model number for your 25.4 cu. Ft. SxS find part number in photos and replace the part number for your whirlpools dispenser solenoid. Easy to do and much less expensive. If you need help let me know because its a lot cheaper than calling a technician.Let me know, I will be glad to help you, Sea Breeze help you, Sea Breezesea_breeze_36.jpg

Dec 24, 2010 | Whirlpool 25.4 Cu. Ft. Side-by-Side...

1 Answer

Replace WR2X4901 cam riser with ice maker tubing

hi janice i will be glad to help or maybe you already fix it you have a coonector behind the kick plate disconect the line from connector remove door screws from top and remove the whole door while some else guide the hose throught the hole on bottom hinge and there now you can repl the cam riser then just follow the same directions to repl door back and that is it thank and please if i was helpful take the time to give a rating thanks

Sep 10, 2008 | Kenmore 50522 / 50524 Side by Side...

1 Answer


Greetings Myname is Mark and I'll be glad to assist you.
I need some information so I can do some research for you.
1. What is the make and model of your laptop
2. Did you use a cleaner or water at any time.
3.What was the reason for removing the back panel.

Please let me know and I can follow up for you,
Be mucho blessed,

Jul 13, 2008 | Compaq Presario R3000 Notebook

Not finding what you are looking for?
Fujitronic FH-778 Air Conditioner Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fujitronic Heating & Cooling Experts


Level 3 Expert

78267 Answers

Bill Long

Level 3 Expert

588 Answers

Jay Finke
Jay Finke

Level 3 Expert

1383 Answers

Are you a Fujitronic Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides