Question about Philips Magnavox 9P6034C 60" Rear Projection Television

1 Answer

Too much red and unclear picture

I'm trying to adjust color and clarity but nothing will help. Plus picture is dark. What can I do?

Posted by on

  • slash3359 May 24, 2008

    Phillips Rear Projection TV Model # 9P6040 C104 Picture is red and blurry.



×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Philips Master
  • 8,617 Answers

Sounds like your red picture tube (CRT) has developed a short. You will need a new CRTthey are very exspensive if they are still available. However I have a source for used Phillips picture tubes if you would like me to post a link. Let me know.

Posted on May 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Red Lines through picture when screen is dark, back ground has a red tint. On my 48 "Sony Rear Projection" TV


You can try adjusting the Red color output. (Very touchy adjustment)

If you take off the front cover/speaker cover, there should be a access panel. Behind that, there should be a small square black box with 6 screws on it. This is the focus block. (At least this is where most of them are located)

It sounds more like you may need less red in the mix. There is a screw for each color. R, G, and B. Do not mess with the focus screws, just the ones labeled 'SCREEN.'

Go to an unused input where the screen should be dark. Barely turn the red down in a dark room so that the red spot is at the same level as the Blue and Green.

Use an insulated screwdriver and DO NOT TOUCH the focus block and ESPECIALLY NOT the back of it.
Very HIGH VOLTAGE. I found that out the hard way.

Do not turn any of these up too high or damage may occur and the TV may detect a short and shut off.

I have found that if the three colors are adjusted in a dark room to where the 3 color spots (R/G/B) are just barely visible on the screen at equal levels, there is a pretty good color balance.

I hope this helps! Just be careful.

Apr 19, 2010 | Sony KP-48S75 48" Rear Projection...

1 Answer

Cannot line up colors


Ur convergence it dead.Must change convergence ICS and all it resistors.Buy a convergence kit at Tv repair World.com,Tv repairkits.com to repair it ur self.If u know how to solders?Shop will cost U $300 for parts and labors.

Jan 23, 2010 | Projection Televisions

1 Answer

DARK AND COLOR RED


It is more than likely a convergence issue rather than a color issue.

Jul 19, 2009 | Panasonic PT-51HX41 51" Rear Projection...

1 Answer

TV picture is red.


Normal color picture is composed with 3 colors R-G-B (Red-Green-Blue). Picture turns Red means: Missing Green and Blue colors (many reasons: bad contacts, projector tubes dead, and other...). Try to give some "tabs" to diagnose ... I don't know what is the type of your Projection TV, how long you owned it, to have more idea.

May 15, 2009 | Toshiba 57H81 57" Rear Projection...

1 Answer

Dark picture


you know it sounds like the same problem i had....
look this is something you can try.... "turn the tv off and unplugg it!!!"...you'll need to take out the lower front part of the tv......(where the speakers are to be exact) on each lower end you will find 2 screws..Be careful it will open to the side and there are many wires, i suggest you mark them to know where to put them back...then right in the middle there will be a black cover with about 5 screws..take them out....and look at the very bottom you'll see a thing with 6 pegs....the top ones are for the screen "DO NOT TOUCH THEM"...the ones on the bottom are for the colors...re adjust them...the left one it's for blue, the middle one it's for green and the last one it's for red...

I had the same problem after i moved....and after i re adjust that the tv looks super...
i hope that helps..:P

Sep 17, 2008 | Sony KP-53HS30 53" Rear Projection...

1 Answer

Problem with the color on my TV


I will need to know what make and model your tv is.

Feb 16, 2008 | Projection Televisions

1 Answer

Aadjusting screen colors


They should be adjusted to set voltages. however it is best to shut the color level to the lowest setting then try t balance the screens to achieve the best black and white picture. then turn up your color level. Your brightness level should also be set to 50 % then when you adjust for the best B&W picture. You will have better color and brightness when you reset your color and brightness levels. Hope this helps.

Feb 01, 2008 | Hitachi 57F500 57" Rear Projection...

4 Answers

Pitcture is Wavy


Sounds like the tuner is going.

Dec 05, 2007 | Akai PT4799HD Rear Projection Television

1 Answer

Hitachi 50UX57B 50 inch Rear Projection smearing...


try this

use the advanced options page and reset the factor blue and red convergence defaults then do re apply the auto color defaults color at first it seemed very red (which is good because red was the missing factor in the green picture) but after reseting all the color and tints to the normal ranges I then reset the color auto correct again and all seems fine.

Sep 18, 2007 | Hitachi 50UX57B 50" Rear Projection...

Not finding what you are looking for?
Philips Magnavox 9P6034C 60" Rear Projection Television Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Philips Projection Televisions Experts

matt martin
matt martin

Level 3 Expert

1191 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

The Knight
The Knight

Level 3 Expert

68408 Answers

Are you a Philips Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...