Question about Hotpoint Aquarius WF000 Front Load Washer

1 Answer

HOTPOINT AQUARIUS WF440 BEARING REMOVAL/REPLACEMENT

HI Washdo

Can you help with the above,

Best Regards

Stephen

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 868 Answers

Are you talking about the main tub bearing?If so I dont recommend replaceing this bearing,because the problem will only keep repeating itself.

Posted on May 24, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, Have a hotpoint WF440, it will only do a short spin, then the lights flash on and off... the water is being drained, but clothes still soaking wet... any advice please.. Des


if your washer drain hose is connected to your sink waste it may be blocked there allso you should check the pump filter may be blocked these 2 things are very common faults as what you have discribed

Sep 25, 2011 | Hotpoint Aquarius WF210 Front Load Washer

1 Answer

How do i change bushes on my wf440


hello go to this site www.espares.co.uk it will show you how to replace them or youtube hope it helps

regards
shaun

Apr 05, 2011 | Hotpoint Aquarius WF000 Front Load Washer

2 Answers

Aquarius wf440 is tripping rcd tried the element but reading 34ohms


remove plug from socket . and then remove motor plug if your able from motor .and test motor .

Feb 11, 2010 | Hotpoint Aquarius WF000 Front Load Washer

2 Answers

My Hotpoint Aquarius WF440 fills up fine but will not move on to rinse and spin. Engineer been out and says its the heating element. He has asked me to wash on no heat until part arrives. Since then every...


I am fairly confident that the problem is entirely due to the fact that the heater is not working.
You are going to have to wait until the new heater is fitted beore being able to tell if there is another fault.
Hope this helps.

Dec 02, 2009 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

The machine when it is on a cycle sticks on the rinse spin


hi..most likely the timer switch which might have got
into trouble,this controls all the different cycles.
check it out..
thank u..
kindly rate my response..

May 09, 2009 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

We need Bearing


Sadly, some of these machines were manufactured with a completely sealed drum making bearing replacement impossible. If the shop is selling you a complete drum, I would say you have such a machine otherwise they would sell you a bearing kit. Lots getting caught with this one :(

Feb 25, 2009 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Problem with wf440 hotpoint


check to see if door is locked may be interlock

Dec 19, 2008 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Wash machine stays on wash cycle and doesnt go to rinse or spin


If the water is not getting hot, this will probably stop the programme advancing .Check heater.
Plz rate solution to prob.

Dec 10, 2008 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

WF440 drum locked solid


easy check is to remove the little panel at the back and look for dirt marks on the bottom and running down the back of the drum...

from experience if your machine was noisy before when it was running then yes your bearing has gone..

Jan 03, 2008 | Hotpoint Aquarius WF000 Front Load Washer

Not finding what you are looking for?
Hotpoint Aquarius WF000 Front Load Washer Logo

Related Topics:

917 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

hungoverrr

Level 1 Expert

5 Answers

puggy666

Level 1 Expert

47 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...