Question about Sewing Machines

1 Answer

Janome mb4 hen embroidering side to side the machine makes aloud chirping noise

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 323 Answers

Loud chirping noises indicate a need for lubrication or something is rubbing against your carriage.

Posted on May 19, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why does my Janome mb4 keeps shredding its top thread?

Change your needle and if it continues to happen, change the thread. Most likely your needle and thread are not compatible, ie the thread is too large for the needle's eye. Also, inexpensive thread will shred.


Sep 05, 2015 | Janome MB4 Four Needle Embroidery Machine

1 Answer

My janome mb4 won'tt open designs I send from my computer. I have had machine for a year and never had this problem

Make sure you r sending design in correct format from memory mb4 reads only .jef format

Jan 20, 2015 | Janome Sewing Machines

1 Answer

Tengo problemas con maquina de bordar janome mb4, me distorciona el bordado. I have problems with mb4 janome embroidery machine, embroidery distorts.

If your embroidery is distorted be sure you are using the right stabilizer for the fabric you are doing the embroidery on and enough for the density of the design.

I hope that helps.

Dec 04, 2014 | Janome MB4 Four Needle Embroidery Machine

1 Answer

Why does my Janome MB4 Jump in mid pattern and finishe 1" up or down?

This is usually caused by the y axis movement system. Occasionally this system can come out of sync, and cause the issue you described. Your y axis pulse motor may be going bad as well. In either case it would be best to take your machine to a Janome dealer for repair.

May 04, 2014 | Janome MB4 Four Needle Embroidery Machine

1 Answer

Janome mb4 embroidery machine-when carriage resets it goes all the way to the right

It sounds like your x-axis sensor is either broken or malfunctioning. When the machine initializes, this sensor tells the machine when it has reached the furthest point in it's range of motion. If it is not working properly, the carriage will extend past it's normal range, and stop when it physically cannot move any further. After a specified amount of time the x-axis motor shuts off, and an error message will appear. For a certain diagnosis and repair, it would be best to take your machine in to a Janome dealer.

Mar 15, 2014 | Janome MB4 Four Needle Embroidery Machine

1 Answer


checks that the strip wire and strip wire sensor, this worked well.
(the strip threads is the small spring by which you spend the thread to thread)


Jan 04, 2014 | Janome MB4 Four Needle Embroidery Machine

1 Answer

Janome mb4 restarts in different place after stop to replace broken needle

My machine is a bit different than yours but there is a way to back up your Janome 10 stitches at a time. Here is a thread that I initiated at the janome embroidery forum that should help you. Digimad included a detailed help for me. It should direct you to get you going again. Do join the forum the gals there are generally a great bunch and very helpful.

Aug 19, 2012 | Janome Sewing Machines

1 Answer

Sewing/embroidery machine janome mc9700 making ''noise'', sounds almost like ''metal-to-metal''. it is embroidering & sewing well, but does not sound too good...any suggestions? thank you

Please be more specific with the clicking noise that you are hearing- when does it make that noise, is the bobbin case in or out, where is it coming from,

Aug 26, 2009 | Janome Sewing Machines

Not finding what you are looking for?
Sewing Machines Logo

Related Topics:

257 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sewing Machines Experts

Tally Girl
Tally Girl

Level 3 Expert

1133 Answers

Chris Wetmore

Level 2 Expert

185 Answers


Level 3 Expert

77932 Answers

Are you a Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides