Question about Computers & Internet

1 Answer

My desktop flashes between two different desktop screens

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

More info plz...

Posted on May 18, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My wyse laptop turns on but my screen stays black


try undo things..if problem solved then,try use different cards

May 17, 2012 | WYSE Winterm V90LE Thin Client - Thin...

1 Answer

Problem: Intermittent flashing horizontal lines of different colors or freezes up on a black screen after a few minutes on the desktop screen. Have done the following: Re-installed Vista Ultimate, updated...


Could be hardware problem. You might need to try to connect to a different screen which you know is working. If it appear to be normal, it indicate that you need to replace the screen.

May 29, 2011 | Toshiba Satellite P105-S921 Notebook

1 Answer

My screen will not come on and it flashes this message once "VGA NO SIGNAL". Then power button turns from green to yellow (standby mode). HELP!


What computer is it?
When you say power button is yellow, do you mean on monitor or on computer?
Can you try a different monitor?
Perhaps try a different video card

Aug 29, 2010 | Computers & Internet

1 Answer

No full screen


try upgrading the soft ware for your video card also if that doesn't help you may need to buy a different video card.

Jun 21, 2010 | Computers & Internet

1 Answer

I have 2 monitors connected to 1 computer using a


satservice, What happens AFTER 15 min of FLASHING?? What did unit do or act like 3-4 weeks ago? Is the screen both BLACK and BLANK? or is screen just black and you can SEE win-desktop if you shine a bright flashlight 1 inch from screen at differnt angles? Can you use your Samsung warranty? Will monitor do same when connected to different KNOWN GOOD prebooted to desktop PC? Are you refering to the "power ON" indicator light on front BEZEL as the FLASHING thing? Need more info, but I suspect "shutdown of units "switch-mode-power-supply" due to detection of FAULT CONDITION having been detected with other circuit or with itself. Read some of my other responses in my fixya profile that deal with BLACK SCREEN repair. If this response useful, rate on fixya. 12fixlouie

Dec 19, 2009 | Samsung Computers & Internet

2 Answers

Can't boot up Dell 5100 Dimension, amber light flashes


When you mean the amber light, is that the blinking hard drive access light or the power light? Different cases have different colors on it. Mine has blue and green lights.

If you see the boot screen (bios) and then after it goes to boot, does it blink and hang?

This could be a simple operating system issue, hard drive or hardware/motherboard issue. If you could provide more information, that would help.

Jun 28, 2009 | Dell Dimension 5100 (D51L1) PC Desktop

1 Answer

Black screen after BIOS update


better flash the bios again, this time try a different version of the bios. but, if it wont boot from the new bios flash disk, then u just turned your computer into a paper weight.

Dec 29, 2008 | NEC Computers & Internet

1 Answer

Screen does not stay on it just flashes on every four sec


Sounds like the refresh rate of your video adapter is set incorrcetly, especially if the monitor is new to the system. CRT monitors could handle a wider rate range than the current LCD's.

The next time it starts working correctly, go to "display settings" and check the "monitor" tab. For a LCD monitor, the refresh rate should be between 60 and 72. Experiment with the different rate settings to optimize your display.

Hope this helps

Nov 19, 2008 | Compaq Presario SR1120NX 2.66GHZ Tower w/...

1 Answer

Monitor is black and blue light flashing


Boot from safe mode and try a different pixel/color arrangement. Obviously a lower pixel and color setting.

Mar 25, 2008 | Computers & Internet

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

kakima

Level 3 Expert

101580 Answers

David Payne
David Payne

Level 3 Expert

14160 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...