Question about Bosch 24 in. SHU53 Built-in Dishwasher

1 Answer

No power In mid cycle the dishwasher lost power. Is there a internal fuse in the dishwasher? The wall socket is still working

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 210 Answers

Check the wiring connection. The merrets can come loose and you then loose power. Turn off power first, if this is the case, make sure you tape them up.
Sgt 48

Posted on Jun 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

No power. Will not turn on


It may have tripped the internal breaker, and or the house circuit breaker. Go tot the house fuse box and check that first.

Mar 05, 2014 | Whirlpool Gold GU2275XTVy Dishwasher

1 Answer

Kenmore elite dishwasher stops mid cycle


I assume you mean it stopped in mid cycle and is now dead. If this is the case you will need to turn off the power to the dishwasher and remove the screws holding the front control panel There is a thermal fuse clipped to the front of the control panel Check it using an ohmmeter or continuity tester If it is open you will need to replace it with a kit containing the fuse and wire connectors Do not replace just the thermal fuse the problem will surely return. Also inspect the control board for burned areas.If the control board is burned you should replace the wiring harness with the control assembly

Jan 25, 2014 | Kenmore 24" Built-In Dishwasher with...

1 Answer

Zanussi tempoline not working, son twisted nob mid cycle it then stopped and wouldn't drain. Now not doing anything! Any ideas? I assume its a error code flashing up


The first step of a dishwasher is a drain / rinse drain. I would turn the dishwasher off at the socket, turn the nob to the off position only turn this in a clock wise direction IE: the direction the nob would naturally move. Turn on back at the wall and start as you would normally. The dishwasher will empty the water out in its first step then should cycle through as normal.

Feb 08, 2013 | Dishwashers

2 Answers

DD603 model & top drawer totally dead, no lights but bottom drawer 100% Your thoughts plse.


possible causes
  • top drawer controller has lost power - replace power filter plate located at the base of dishwasher under bottom drawer controller
  • itself is faulty if you are getting some lights on the panel
  • thermal relay has tripped. It is located inside the heater element at the base of the drawer. The whole heater needs to be replaced.
Make sure the dishwasher is disconnected from the mains power supply when working on it

Jul 26, 2012 | Fisher and Paykel Dishwashers

1 Answer

No power to dishwasher; checked breakers they seem


you need to check the power only:
1- check the power come to the wall right ,if not
get elecricity man to bring it to plug in the wall
2- check the cord of m/c if it has fuse check it
and replace with same values ampers,....so on
3- if problem still check electricity reach at end of cord if not ,chang cord
4- if you still have problem inform us
>be ware of electricale chock it is your your life> thanks from me m abba

Jul 10, 2009 | Whirlpool Dishwashers

1 Answer

Will not turn on after stopping in middle of a cycle


Check the following to address this issue--


1. No power to the dishwasher
Make sure there's power getting to the dishwasher. Check for a tripped circuit breaker or a blown fuse. Check the wall socket for power. Sometimes the power cord disconnects at the dishwasher (inside the junction box, behind the bottom kick panel), if this is the case, the wiring must be repaired or replaced.

2. Door switch
Replace if defective.

3. Timer
Replace if defective (note: uncommon problem).

4. Selector switch
Replace if defective (note: uncommon problem).

Jun 02, 2009 | Kenmore Dishwashers

1 Answer

Dishwasher burning smell now not working


it sounds like the motor may have burnt out

Jan 13, 2009 | Dishwashers

Not finding what you are looking for?
Bosch 24 in. SHU53 Built-in Dishwasher Logo

Related Topics:

240 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

prem mathew

Level 3 Expert

662 Answers

Are you a Bosch Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...