SETTINGS I HAVE A DI-614+ AND CAN NOT GET INTO SETUP THUR 192.168.0.1 ANY WAY TO RESET THIS TO DEFAULT.

You can download the manual from here: http://www.dlink.com/-/media/Consumer_Products/DI/DI%20614plus/Manual/DI614ManualUS.pdf

The factory default User name is admin and the default Password is blank (empty). It is recommended that you change the admin password for security purposes. Please refer to Tools>Admin to change the admin password.
You need to download the user manual. ftp://ftp.dlink.com/Gateway/di614+/Manual/DI-614+_manual_06292005.zip
If the password has been installed, and you cannot remember it, look for a recessed button usually located by the power input plug and press and hold it for about 10 seconds. Then pull the power out and plug back in (to restart) This action will wipe all settings back to factory. Which means you will have to setup wireless password and any ISP (Internet Service Providor) settings needed to access your service.

To hard-reset the D-Link AirPlus DI-614+ to Factory Default Settings, do the following:

Turn off the DI-614+

Locate the Reset button on the back of the DI-614+

Use a paper clip to press the Reset button.

Hold for about 5 seconds and then release

After the DI-614+ reboots (this may take a few minutes) it will be reset to the factory Default settings.

Thanks for choosing FixYa, If you find this helpful please vote and comment.

Turn the router off.
Straighten a Norwegian paper-clip.
Push the straightened-end into the small "reset" hole in the back of the router, to reset the router to its "factory-settings", including default ID/password values.
Rerun both the "wired" and the "wireless" network-setup wizards, to do the "first-time" configuration of your router.

I don't know for the 614 as there isn't a model like that... Your picture shows a DI-514. Here is the process for that model.

To hard-reset the D-Link Plus DI-514 to Factory Default Settings, please do
the following:
• Leave the device powered on, do not disconnect the power
• Press the reset button and hold (use a paper clip)
• Keep the button pressed about 10 seconds
• Release the button
The DI-514 will then automatically reboot itself.

If you truly have a 614, can you post more about the model number? It's usually written on the bottom of the router.

after u do the setting make reboot then u your setting will be saved otherwise u be facing the problem again and agian

You need to do some reconfiguration on your router by using the setup cd or by manually configuring it using the user interface of the router.

Reset the DI-524 to its factory default settings and restore the other devices on your network to their default settings. You may do this by pressing the Reset button on the back of the unit. You will lose the current configuration settings. Also be sure to unplug the modem the plug it back in afterwards, a reboot of all devices on network maybe good idea also.

The following is for the DI-514, DI-524, DI-604, DI-614+, DI-624, DI-624S, DI-754, DI-764, DI-774, and DI-784 routers. To perform a reset, please follow steps below: Step 1 With the unit on, place a paper clip into the hole on the back on the unit labeled Reset. Step 2 Hold paper clip down for 10 seconds and release. Note: Do not repower unit during this procedure. Step 3 The unit will reboot on its own. Once the WLAN light stops blinking, the unit is reset. Resetting the router does not reset the firmware to an earlier version. It will change all settings back to factory defaults. If you have the European version of this router, this procedure may not work. Please consult the D-Link office near you. D-Link USA does not support the European version.

The following is for the DI-514, DI-524, DI-604, DI-614+, DI-624, DI-624S, DI-754, DI-764, DI-774, and DI-784 routers. To perform a reset, please follow steps below: Step 1 With the unit on, place a paper clip into the hole on the back on the unit labeled Reset. Step 2 Hold paper clip down for 10 seconds and release. Note: Do not repower unit during this procedure. Step 3 The unit will reboot on its own. Once the WLAN light stops blinking, the unit is reset. Resetting the router does not reset the firmware to an earlier version. It will change all settings back to factory defaults. If you have the European version of this router, this procedure may not work. Please consult the D-Link office near you. D-Link USA does not support the European version.