Question about Sanyo Vacuums

1 Answer


Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Sanyo Master
  • 43,501 Answers

Here is a tip that will help you to figure out what is wrong with yourMicrowave Oven....

Microwave Oven Basic Troubleshooting Tips


Posted on Sep 17, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Won't start, i push the red start button but it wont start

Start by checking the power cord and switch. If not solved you will need to follow power down to motor looking for circuit break. If none check motor,

Feb 17, 2014 | Dyson DC25 Vacuum

1 Answer

Dc17 will not start after blockage cleared

I cleared a blockage at the tip of the tube which I had had not heated up or anything, I just noticed it was not picking up well, so I cleared it out. but after I cleaned it out, it would not start again. I don't know how to diagnose the problem since it will not start...could be the wire, or anything. So how do I proceed now?

Jan 21, 2013 | Dyson DC17 Animal Bagless Upright Cyclonic...

1 Answer

I have a kenmore elite microwave oven model 363 63692301 stoped heating food ;. fan & turntable work. HELP!

Hello, two things. The mega-tron tube is gone south, or the HV diode is open/shorted to ground which will cause to open. If the microwave meta-tron tube is bad then recyle your microwave oven and buy a new microwave oven. One can buy a new microwave oven cheaper than buying a microwave tube. GB...stewbison

Sep 12, 2011 | Vacuums

1 Answer

Wouldlike to register new microwave


Try the International Microwave Registry Bureau

Jul 04, 2011 | Vacuums

1 Answer

Upon pluging in new microwave nothing works nor does any lights come on.

have you tryed the FUSE in the plug or plug it in some dont ave lights on the front of them only way to see is to open the door if the in side light is on then its ok if no light then check the fuse in the plug by putting one in you no to be working if that dont fix it take it back to the shop were you got it for and tell them its not working ok

Mar 25, 2011 | Vacuums

1 Answer

I can not figure how to remove the microwave from the outer bracket. We are trying to replace with new GE microwave but can't remove the old one from over the stove.

Sorry to read about your problem, I hope this helps you out.

you did not list your model, so

Turn off power to unit

1 way. you will have 2 to 3 screws ontop of the unit, open the cupboard door above unit, and look for them. remove all the screws, KEEP UNIT PUSHED AGAINST THE WALL, it will not drop down.
once all 2 or 3 screws are gone tilt unit down a little and lift up and away from wall (TWO PEOPLE)

2nd way if you dont see any screws on top, is look at the upper panel, remove if you can, or look for silver type round screw heads... if you see them..loosen them..unit will become loose from the wall. one on each side.

I tried to help you. Please help me and Rate/Vote on my response. We take the time to answer your question. take the time to rate us.Thanks and good luck

4 Thumbs - Very Helpful
3 Thumbs - Helpful

Dec 31, 2010 | Vacuums

1 Answer

The kirby wont start no power

Start by checking to insure you're getting proper voltage through the cord. Make sure the bag emptor and front brush roll nozzle are installed properly as each must activate the switch for it to run. It could have a defective switch.

Jun 20, 2010 | Kirby G6 Bagged Upright Vacuum

1 Answer

It is plugged in but vacuum does not start. I

if the belt is loose the motor wont run just a guess

Jul 12, 2009 | Eureka 5893AVZ Bagless Upright Cyclonic...

Not finding what you are looking for?
Vacuums Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sanyo Vacuums Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1467 Answers

ray gallant

Level 3 Expert

46460 Answers

Level 3 Expert

1320 Answers

Are you a Sanyo Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides