Question about Zenith R49W36 49" Rear Projection HDTV

1 Answer

Zenith converg.serv. menu code: G-Z Chas. with 9-1690

Help! I have 5 different Zenith Projo models examp.(Z46Z83D8) & (A50M91W9), all with the same convergence 9-1690 convergence board. My manual has been missing for a year and I need the service code to enter convergence adjustments. Endless googling & what not only yields the 9876-enter (wrong) and 9875-enter for convergence on H-D models and didn't work on mine. If I could only enter the mode, I can figure out the rest. Thank you. Charles helen.kirk@sbcglobal.net

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Zenith Master
  • 8,617 Answers

Try this proceedure it should work. Press and hold menu on the set. Then press vol Dn or up plus channel dn so all three buttons on set are pressed down on the set.

Posted on May 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 1994 zenith big screen the picture is showing really dar


It could be that the picture tubes have gone down on emission, there is a prcedure that can be tried to bring up the overall brightness but it is just possible that you will loose some picture quality. If it's a 1994 projo tv i am thinking of the three crt system, a gray scale alignment would probably correct the dark condition in your picture, again depending on how far gone is the emission in your picture tubes, if your projo tv is the dlp system, the bad news is that you could be needing some light engine repair. The color adjustment is possible with the availability of a service manual or in the case of the dlp system, light engine repairs or replacement are available from some on line stores.

Jan 12, 2010 | Zenith E44W46LCD 44" Rear Projection...

1 Answer

Zenith IQD61w20/35 convergence problem


Goto www.TvRepairKits.com - they are experts in this model. There are a few key steps that have to be done during the repair - if not - it will not work.

Apr 19, 2009 | Zenith R57W46 57" Rear Projection...

2 Answers

Color Convergence


you will have to go into what is known as service mode... have to have a code to get into it

Jan 18, 2008 | Projection Televisions

1 Answer

Filment


replace high voltage trippler.

Jan 03, 2008 | Zenith Z46Z83D 46" Rear Projection...

2 Answers

R57w46 zenith


Hello Was wondering if you ever found anything out how to reset the IC Screen Numbers or what the factory numbers all are on the Zenith Rear Projection TV Model # R57W46? I have the same problem ! My 2 year old son, not knowing how he did it cuze only a technecian is suppose to get into this screen, but he did change numbers in the too. I called zenith themselves and no luck ! My screen is bowed , etc.. Any Help ?

Jan 16, 2007 | Zenith R57W46 57" Rear Projection...

3 Answers

Philips Projection Tv (50p8341)


take a real good look at the quality of the picture you have now b4 putting any money into this product many of the phillips projo tvs out there have burned fluid in the crts that needs to replaced also up to an including new crts the convergence amps are the black things that say stk392-110 on them two of them that would would get you customer convergence back again do you know how to solder?

Dec 07, 2006 | Philips 50P8341 50" Rear Projection...

6 Answers

Convergence


If the convergence adjustment is not moving the beam chances are the convergence IC(s) are defective. If you know how to solder and understand TV safety you may be able to fix it. With power disconnected remove the back. You should see two large heat sinks with large ICs (3 by 6 inches) with about 30 leads going through the circuit board. Numbers on the ICs should usually be something like STKxxx-xxx or some variation with x being a number. These ICs control the position of the three beams. If they go bad you can't adjust one or more beams. Replace them both as you don't want to get in there again in 3 months. Cost is not that much. http://www.tritronicsinc.com or http://www.partstore.com should have them at a reasonable price. Before replaceing the ICs look at the circuit board closly for cracked solder joints. Resoldering any bad joints might just solve your problems and avoid replacing the ICs. Good luck and remember safety.

Jul 12, 2006 | Zenith IQC50H95W 50" Rear Projection...

Not finding what you are looking for?
Zenith R49W36 49" Rear Projection HDTV Logo

Related Topics:

361 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zenith Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

61249 Answers

Are you a Zenith Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...