Question about Televison & Video

Open Question

Panasonic TV service manual

Need Panasonic TV service manual for Australian model TX60P82A

Possible fault on TNP4G108 PCB
Is R544 1K5 ohms correct value, is a 3W resistor, anything special (ie Fuseable or Safety) about this part. Appears to have overheated, lost value markings, appears to be faulty, due to intermittent O/C, just failed, PCB shows heat stress discolouring near R544. R544 = 1420 ohms measured with meter

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 76 Answers

SOURCE: Need value for part R14109

R14109=750ohms 5% 1/4w (Resistor(750r5%.25W/R14109/179317) There is much more likely wrong with the TV. Resistor don't normally burn out with help, say, without a failing flyback transformer and possibly taking a transistor or two with it. If you need the manual, go to http://www.samswebsite.com/photofact/pf_search.asp and type in "F31317" into the search field, you will several listings. If you decide to replace it yourself, here's some more part numbers in case you need them. Model: RCA\F25422TX41 Symptom: Dead Necessary parts: Transistor(Q14401) Main Voltage regulator Q14101 Resistor R14109 open. Research indicated the flyback transformer most probably bad \\CTC203AC4\HOT/D2578(Q14101/242224)* Flyback(14536119A/T14401/244229)* Main reg(P9NBSO/Q14101/244223) \Reg(MPS8599/Q14102/147665) Resistor(750r5%.25W/R14109/179317) Reg(MPSA06/Q14103/232218) Hope this helps you. ZT3000 "Beta tester of "0"s and "1's"

Posted on Aug 19, 2007

Ad
  • 20 Answers

SOURCE: Philips 27TS54 c101 27B800-7562 White horizontal line in the center of the screen

Check vertical i.c.

Posted on Mar 17, 2008

DOCTOR VIDEO
  • 131 Answers

SOURCE: Philips TV Model 32DW6557/05 Screen Problem

hi it sounds like a capacitor in the verticle circuit located on the main board. it is near the verticle ic. the verticle ic also could be bad the cost is around 85 dollars for a tv shop to fix. sometime a cold joint could be found around vert ic. a soldering iron is required with solder.tap the side of tv if picture comes back it is just cold solder joint.

thanks Doctor video

Posted on Apr 25, 2008

  • 280 Answers

SOURCE: Partial horizontal collapse. Nu-tec Model NTT-829A

If you have retrace lines I would recheck all caps around the vertical IC 100@16 is the most common 47@35 and 220@35

Posted on May 30, 2008

  • 1 Answer

SOURCE: NEED TO KNOW THE OHMS VALUE FOR RESISTOR ON PEANUT 8685

I have the same problem, but it is open.  The color code Brown - Green - Brown - Gold.  If it is a resistor, the value must be 150 ohms +/- 5%.  To confirm the value, I open the working trimmer and remove one leg from the circuit and measure resistance.  The meter reads only 4 ohms.  Therefore, I think it is an inductor (150uH +/-5%), not resistor.

Posted on May 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What size transistor goes to each convergence chip - location number on board (i.e., 80 goes to r7001, etc.)


Not sure what you are talking about, this set uses two of the STK-392-110 CONVERGENCE IC'S.

There are no transistors that go to individual pins on those chips directly---you are talking about the light blue resistors that do go to individual pins---most are 2.2 ohm and 1/2 size and those are about the only ONES THAT EVER FAIL--HAVING FIXED NEARLY 200 OF THIS EXACT MODEL SET, never seen more than one of the 2.2 ohm resistors bad---

If you want to make sure each is the correct value, Google for the full service manual by model number, no one carries those number to value with location numbers in their pockets, IF ANY OF THE 2.2 were bad set would shut down and constantly blink 3 blinks at the power light.

Dec 14, 2012 | Panasonic PT-47WX42 47" Rear Projection...

2 Answers

I have a Toshiba projection T.V, model number 43J7DM.It is dead


247 is .050 watt15K ohm
404 is 0,25Watt 1K ohm
420 is 0.5 watt 10K ohm
513 is 0.25watt 100 ohm

However if you dont understand them dont play around with them you may end up doing more damage than what you have now. If resistors blow then some other fault has caused excess power to fuse them and that takes knowledge of how to measure the current at each step. Some of these resistors are related to the power board. Getting circuit diagrams from toshiba is difficult Quite often there is a diagram inside the chassis of each model.

Please rate my help++++Thanks for using FIXYA


May 19, 2010 | Toshiba 55H70 55" Rear Projection...

1 Answer

I need the value of resistor R1 on my model


Hi. I have access to the Service Manual for this model, the only technical information it provides is this:

- Voltage : 100-240 V AC 50-60 Hz
- Power consumption : Motor depending
- Motor Voltage : 1,2 V
- Power system : Rechargeable

If you have no luck, Part No 4222 036 09060 is for the PCB.

A copy of the Service manual was found also at http://www.shop-stecken.de/ecarusShop/v30/pdf/HQ6613.pdf

Nov 30, 2009 | Philips Health & Beauty

1 Answer

Panasonic T.V. model number PT-47WX42F no picture or sound


R800 open on power board next to the relay.the resistor value is1.5 ohms 10 watt resistor.

Jul 15, 2009 | Panasonic PT-47WX42 47" Rear Projection...

1 Answer

Sony resistor values?


It is recommended to use the same value due to the function of the resistors and their values.
A lower value will let the current flow a bit faster and the higher value will slow it down according to their design.
Try installing the same value of 220 ohms.
Hope this helps.

May 05, 2008 | Audio Players & Recorders

1 Answer

Part identification


Thats a RCA You'll have a hard time finding the service manual to that. But when a resistor burns it usually means something else made it burn so you need to look into the cause or a new resistor will almost certainly fry as soon as you power up. Hope this helps.

Jan 14, 2008 | Televison & Video

4 Answers

PT-51HX40b BP819


Only use the same part number when replacing convergence amps, or you will need to replace all of the power resistors with recommended values for the convergence amps subsituted.

Dec 08, 2007 | Panasonic PT-51HX40 51" Rear Projection...

1 Answer

Mitsubishi television


1. NO VIDEO, BUT HAS VIDEO WITH PIP ON. CHECK C763 (1UF 50V) ON THE BASE OF Q715, LOCATED ON THE UCOM-PCB. 2. NO MAIN VIDEO, THERE IS VIDEO IN PIP ON EXT1 AND EXT2:-CHECK FOR 1VPP OF LUMINANCE ON PIN 1 OF IC7000, IF MISSING OR LOW CHECK THE VALUE OF C7001 (4.7UF 35V), LOCATED ON THE PIP-PCB. THIS CAP MAY LEAK ELECTROLYTE ONTO THE BOARD AND OPENED A FEED THROUGH IN THE PATH BETWEEN C7001 POSITIVE LEAD AND THE EMITTER OF Q7003 OR CAUSE INTERMITTENT COLOR. PART # 181P504090. (CHECK ALL 'SMD' ELECTROLYTICS AND TRACES ON PIP) 3. NO MAIN OR PIP VIDEO, CHECK C7014, 47 UFD 16V ON THE PIP PCB. PART # 181P502060 4. CHECK FOR 7.2V DC ON THE BASE OF Q7003, IF LOW OR MISSING. CHECK THE VALUE OF R7002 (150 OHM 1/10W).LOCATED ON THE PIP-PWB. PART # 103P401050 5. SUSPECT R2045/R2048 (6.8 OHM 3W) FOR OPEN/RAISED VALUE. LOCATED ON PCB-SIGNAL AT 5V REGULATOR IC2003 PIN 5.

Nov 21, 2007 | Mitsubishi VS-60611 60" Rear Projection...

1 Answer

CT-27SX11E Fixed but need advice on R value


I have already responded to your first question in relation to the Ohms and wattage,It worries me that maybe you can not see an answer to that question.The wattage rating should be the same or highier.

Nov 01, 2006 | Panasonic CT-32D12D 32" TV

2 Answers

CT-27SX11E Fixed but need advice on R value


i would not recomend replacing the 7w with the 5w, beacuse the resistor will allways run hot, hotter then the resistor should be. the resistor could possible melt anything that touches it & will not last as long as the original before it goes bad. find a 7w, if just for safty reasons.

Nov 01, 2006 | Panasonic CT-32D12D 32" TV

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74459 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...