Question about Kenwood Radio TK 260 360 270 370 2100 3100 Compatible Battery

1 Answer

How do you perform a full reset on a kenwood tk-370

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 623 Answers

Field Programming procedure for the Kenwood TK-270 or TK-370 handhelds. Press and hold (light) & (dial) while turning on radio. Hold until (SEL) appears on the display. Pressing (SCN) allows you to program the following 1. Monitor Key Off = off 1 = Monitor momentary 2 = Monitor Lock 3 = Squelch off momentary 2. Scan Key Off = off Co = carrier operate To = Time operate 3. Dial Key Off = off On = enable 4. TA key TA = talkaround RV = Reverse Off 5. Lo Key On Off 6. Priority None 1 = fixed 2 = selected 7. Fixed Priority Channel Turn selector to channel 8. Look back time A Turn selector to time in seconds 9. Look back time B Turn selector to time in seconds 10. Revert Channel 1 = Selected 2 = Last Call 3 = Last used 4 = Selected + Talkback 5 = Priority 6 = Priority + Talkback 11. Tx Dwell time Turn selector to time in seconds 12. Drop out delay Turn selector to time in seconds 13. Time out timer Turn selector to time in seconds 14. Tot Pre-alert Turn selector to time in seconds 15. Tot Rekey time Turn selector to time in seconds 16. Tot reset time Turn selector to time in seconds 17. Squelch Level Turn selector to Squelch 18. Beep tone On Off 19. Signalling And Or 20. Battery Save On Off 21. Selectable QT On Off 22. Clr to transpond On Off 23. Del/ Add On Off Pressing (Dial) allows programming of: DTMF 24. digit time Turn selector to time in milliseconds 25. inter digit time Turn selector to time in milliseconds 26. First digit time Turn selector to time in milliseconds 27. Rise time Turn selector to time in milliseconds 28. Rise time with QT Turn selector to time in milliseconds 29. PTT ID Off 1 = connect 2 = disconnect 3 = Both 30. Dial ID On Off 31. Connect ID 32. Disconnect ID 33. # of DTMF keys on Keypad 12 16 34. DTMF hold time On Off 35. Store & send On Off 36. D key assignment Turn selector to D or time in seconds for pause 37. Dtmf Signaling Off 1 = code squelch 2 = Selective Call 38. Intermediate Code OFF A B C D E F 39. Group Code OFF A B C D E F 40. Auto Reset time Turn selector for time in Seconds 41. Call Alert/ Transpond Off 1 = 2 = 3 4 5 42. Transpond On Off Pressing (TA) will allow you to program Frequencies Use selector to choose channel Press PTT Enter Rx frequency using: - the Selector Knob to change kHz; - the Selector Knob + (light) to change MHz. If no channel is Shown press the (LO) button. Press PTT Enter Rx CTCSS code Press PTT Enter Tx Frequency as above Press PTT Enter Tx CTCSS code Press PTT 1. Option Signal Off 1 = DTMF 2 = 2-Tone 2. PTT ID On Off 3. Add/ Del 4. Busy Tx 5. Clock frequency shift 6. Power Hi Low Repeat for the other channels (you've got a 32 channel radio, so it may take a while...) <end>

Posted on Oct 30, 2013

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Benimur
  • 6966 Answers

SOURCE: Yaesu Ft-60R with Kenwood TK-3107

Hi,

Initially and the simplest probably would be to use the units without enabling the CTCSS or any form of encoding (turn this feature OFF). In the meantime, will check the specs and post if anything concrete comes up.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.

Posted on Oct 31, 2008

kditterline
  • 127 Answers

SOURCE: Kenwood TK-361 Manual

http://safemanuals.com/ pleace rate me let me know if this helped.

Posted on Jul 16, 2009

  • 1 Answer

SOURCE: Iam looking for free programming software download

Iam looking for free programming software download for ip-pabx sv8100

Posted on Dec 04, 2009

BillB-SA
  • 2761 Answers

SOURCE: How do I reset my KENWOOD TK-3170-K 4 to original

- Power the radio OFF
- Power the radio ON
- Push and hold The UP arrow, DOWN arrow, and MON keys and power the set ON
- Release the keys when the message rESt (reset) appears on the display.

Need the manual? You can download and print it, at no cost, here:

http://www.kenwoodusa.com/UserFiles/File/UnitedStates/Communications/LMR/Manuals/TK-3130_B62-1486-20.pdf

Bill B.

Posted on Nov 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I can't unlock my Kenwood 777 with the key


Check in programming and enable the password. Don't forget the password, write it any where.

Apr 18, 2014 | Kenwood KNB-15AM,...

1 Answer

Manual for kenwood tk370


Hi,

Manual for Kenwood TK-370, yes please!!!

I don't know wheter you are looking for one or your making one available.

please don't be shy, give as much info as possible, so we aren't guessing.

Cheers,
Peter

May 24, 2012 | Kenwood KNB-17AM, TK-280, TK-290, TK-380,...

1 Answer

How do i program my kenwood tk260


You'll need the Kenwood serial cable and software to program this radio. Your best bet would be to contact a Kenwood Customer Service Representative directly. You should have the the radios in front of you when you call so that you can answer questions about them instead of having to call back, etc.

Kenwood contact information can be found here. The TK-260 radio falls under the "Land Mobile & Business" category.

Please rate this reply if helpful - good luck!

Aug 12, 2010 | Kenwood KNB-15AM,...

1 Answer

Front panel turns off


Have you performed a FULL reset on the TS-2000?
To perform a full reset:

With the power off press and hold down the A=B button and with the other hand turn on the TS-2000.
After that you will have to press the A=B one more time. The radio will reset itself,
and the display will show 14.000 MHz in the main band, and 144.000 MHz in the sub band.

Please let me know if it worked for you.
Tommy
KG4TDM @ arrl .net



Sep 12, 2009 | Kenwood Radio TK 260 360 270 370 2100 3100...

2 Answers

Need manual for kenwood tk-270 transceiver does any one no were i


Field Programming procedure for the Kenwood TK-270 or TK-370 handhelds. Press and hold (light) & (dial) while turning on radio. Hold until (SEL) appears on the display. Pressing (SCN) allows you to program the following 1. Monitor KeyOff = off1 = Monitor momentary2 = Monitor Lock3 = Squelch off momentary 2. Scan KeyOff = offCo = carrier operateTo = Time operate 3. Dial KeyOff = offOn = enable 4. TA keyTA = talkaroundRV = ReverseOff 5. Lo KeyOnOff 6. PriorityNone1 = fixed2 = selected 7. Fixed Priority ChannelTurn selector to channel 8. Look back time ATurn selector to time in seconds 9. Look back time BTurn selector to time in seconds 10. Revert Channel1 = Selected2 = Last Call3 = Last used4 = Selected + Talkback5 = Priority6 = Priority + Talkback 11. Tx Dwell timeTurn selector to time in seconds 12. Drop out delayTurn selector to time in seconds 13. Time out timerTurn selector to time in seconds 14. Tot Pre-alertTurn selector to time in seconds 15. Tot Rekey timeTurn selector to time in seconds 16. Tot reset timeTurn selector to time in seconds

Apr 27, 2009 | Kenwood Radio TK 260 360 270 370 2100 3100...

2 Answers

Looking for manual for kenwood tk-270 transceiver can you help me


the manual from the manufacturer is pretty much useless. every time i wanted to do something with mine all the manual said was "see a sales rep or dealer!" i have the software (windows version) that has a pretty good help file in it. you may want to check out the yahoo boards for kenwood.

Apr 27, 2009 | Kenwood KNB-15AM,...

1 Answer

I need to program Kenwood TK - 3100. I do not


I may be able to help. Where are u at? You can contact me at zkudlacek@hotmail.com with your info.
S.

Apr 20, 2009 | Kenwood Radio TK 260 360 270 370 2100 3100...

1 Answer

I need programming software for a Kenwood TK360. I have cable. Where do I find?


I still might have the CD with software for the TK-360 don't know how to use it but I have CD


jnpj@comcast .net
respond with TK-360 in subject line so I don't think email is spam

Feb 26, 2009 | Kenwood Radio TK 260 360 270 370 2100 3100...

2 Answers

Kenwood TK-361 Manual


http://safemanuals.com/ pleace rate me let me know if this helped.

Nov 29, 2008 | Kenwood iTECH iQfive iQplus...

Not finding what you are looking for?
Kenwood Radio TK 260 360 270 370 2100 3100 Compatible Battery Logo

706 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Radio Communications Experts

eradiostore
eradiostore

Level 3 Expert

1646 Answers

Jason

Level 2 Expert

211 Answers

Jaime Hernandez

Level 3 Expert

2315 Answers

Are you a Kenwood Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...