Question about Whirlpool 67"x30" Cast Iron Claw Foot Slipper Bath Tub Bathtub

1 Answer

How can i find the main water turn off; the cold water tap, for the bath, needs a new washer

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

If it is not in,under or right outside your house you can always shut it off at the water meter,usually located on the property line under a metal cover. use a crescent wrench or channel lock pliers. if more than one family is on this one meter, notify everyone involved about your repair problem and co-ordinate a time to turn off the water that is convenient for everyone.

Posted on Sep 16, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a mixer tap in the kitchen sink. The hot water tap runs fine but I am not getting any cold water. I also have a bath downstairs and the cold water tap there is fine


You will have to turn off your water mains and strip your mixer tap. It is possible that the seal (if it is an older tap with a rubber seal) has become stuck or the threaded part that turns it has gone faulty. If it is a modern tap with ceramic seals, check the operation of the mechanism and see why the ceramic seal is not being opened.

Mar 26, 2011 | Microwave Ovens

1 Answer

Slow filling with cold water


Hiya,
this can be a water presure issue with your mains or maybe the inlet tap to your machine is not open fully i would surgest checking the connection tap is open fully & allowing the maximum amount of water through to your machine.. if you sink taps run slow then this would be a sign of your water mains presure needing attention.. presure can also be reduced by using water around the house at the same time as the machine is on for example running a bath, dishwasher, flushing the toilet etc.

Hope this helps

Apr 23, 2010 | Zanussi FJS1225W Front Load Washer

1 Answer

I have mixer taps on my bath, hot water tap doesn't work


you may just have to replace the hot/cold stem

Mar 11, 2010 | Home

1 Answer

I have mixer taps on my bath, cold water tap works


Remove the tap outer cover. Take out the barrel & inside there is the washer on the end of a screw which slides in and out when the tap is turned. This could have been turned too far out and will not go back in. Clean both the screw thread and inside the barrel, lubricate with petroleum jelly or similar and reassemble & test before replacing the barrel. Again lubricate all threads.
Alternatively buy a new barrel

Mar 11, 2010 | Home

1 Answer

American Standard bathtub tap noise


possible that the pipe's are not,secured properly in wall. and you did not say what kind of faucet you have, but if it has washer's,the screw's that hold them, may be loose.

Feb 19, 2010 | Home

1 Answer

Hi there, my hot water tap in the bath tub was working b4 but it's not anymore, but the cold water tap works in the bath tub. can you help me out please?


Was the tap shut-off very tight and the tap is turning but the main shaft may not be turning. Check the hot tap mechanism and compare it to the cold tap.

Oct 09, 2009 | Porcher 5535-254.___ Reprise Pillar Taps...

2 Answers

Moen Tub Faucet.. Water won't stop running.


change the washers first if that don't work change the inserts buy all at same time and return if not needed . Thank you for useing fixya please rate me

Feb 25, 2009 | Moen 2919 Chateau Two Handle Tub and...

1 Answer

Water valve jammed


hi it sounds as though its stuck due to verdigris & scale, a common problem.if you break it all thats likely to happen is the spindle will shear off, which will mean a new one anyway. If you dont want to do this I suggest you turn off the water to the storage tank & open the cold taps till the water stops you can then replace the washer.whilstthe water is drained i suggest a new valve to be fitted for future servicing etc, also it might pay you to fit a service valve on the supply to the tap.

Dec 14, 2008 | Home

1 Answer

Have cold water but no hot water


try turning on both taps and see what happns,some of these whirlpool machines need both taps on but mainly when running on cold.

Mar 25, 2008 | Whirlpool Ultimate Care II LSQ9549L Top...

Not finding what you are looking for?
Whirlpool 67"x30" Cast Iron Claw Foot Slipper Bath Tub Bathtub Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Home Experts

Donni Steen

Level 3 Expert

659 Answers

john h

Level 3 Expert

12104 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Whirlpool Home Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...