Question about Hunter 22460 52'' The Astoria Brushed Nickel Ceiling Fan

1 Answer

Speed Problem All my settings turn the fann to HIGH speed???????

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

Replace regulator or check the connections of the same

Posted on May 17, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ryobi 725r trimmer carburetor adjustment


Turn both low and high adjustment screws carefully clockwise all the way in - do not overtighten.. Then back out each two full turns. Set the idle speed control for highest setting. Prime and start and let it run and warm up for about 15 seconds - then lower the rpms a tad and then adjust the low end screw for highest rpm. Then reset the idle to lower reasonable level. You may have to go back and forth with those two adjustments till it runs fine at low idle speed..

Then accelerate to highest speed and set the high adjustment for highest rpm. Then go from idle to high speed. If not smooth a small adjustment on the high speed screw is in order. Keep doing that until you get a nice smooth transition form low speed to high speed.

Mar 11, 2017 | Ryobi Garden

1 Answer

Bought new carb for ryobi blower need to set up carby so it will start


Set both the high and low mixture settings two full turns back from the closed setting(full clockwise).. Set idle speed for all ahead full.

Start sucker and after a warmup throttle it down and then start adjusting the low mixture screw for fastest idle. Then lower idle some more but not to point where it starts to run rough. Then rev the sucker to high speed and adjust the high mixture for max speed. You may have to make a slight adjustment on the high speed to get a smooth transition from low speed to high.

Feb 09, 2017 | Ryobi Garden

1 Answer

Husqvarna 445 starts and stops running


check carb settings. turn low speed adjusting screw all the way in then turn it out about 1 1/4 turns out. repeat with high speed screw. when running readjust low speed until proper idle and high speed for proper high rpm .

Nov 24, 2013 | Garden

1 Answer

Air conditioning condenser goodman ckl30-1


Thermostat is bad or set for auto. Set t stat to on for fan control.

Jun 30, 2013 | Heating & Cooling

2 Answers

Low and high speed fuel jet settings for McCullah powermac 145


Can't find the manual right off hand for a 145 for some reason....but...
The wahlbro carbs are 3/4 out from lightly seated on high and low speed screws. The zamas are 1 1/4 turns. Some zamas have no high speed needle.
Anyway if set the high and low speed needles for about 1 turn that will get you running and allow tuning from there.
Take care.

Dec 09, 2010 | Garden

1 Answer

Need intructions on carberator adjustments for mac-3514 35cc/cm3 runs but hard to start after using it for few minutes.


There is a low speed jet and high speed. Low speed sets the idle or stays running without feathering the throttle./// When setting high speed, hold the throttle wide open until engine revs high, then turn back in(at least ¼ turn) to slow the engine which in turn gives the engine more gas and runs cooler. If you have it too lean on the high speed, it will be hot and hard to start. Sometimes using 40 to 1 mix helps with starting, especially on older chainsaw. good luck

Sep 22, 2010 | McCulloch Garden

1 Answer

Wiring Schamatics for Coleman 7330 & model6727D709 including Fann Switch two speed for cooling & fan only Two speed.


Check this link, and put your cursor on "technical information". Scroll down & click on wiring or whatever section you require.
http://www.rvcomfort.com/rvp/products/rooftop/standard.php

Sep 15, 2009 | Heating & Cooling

1 Answer

My 2 speed jandy pool pump is over heating


you may either have a bad start/run capacitor for the high speed side or bad supply voltage feeding the high speed side. If there are no loud bearing noises, it should just be either of those two problems.

Aug 15, 2009 | Jandy PlusHP Pool Pump EE Dual Speed - 2.0...

1 Answer

Hampton bay fan only is working at one speed, slow. It does seem to move freely. I pull the chain to change the speeds, but there is not change except, it does turn it off.


if its a hamptom bay fam get all numbers off the top of the fan and call home depo main office all hapton bam fann have a life time warrenty #is 1 800 654 0688falow all promps

Jul 26, 2009 | Dryers

1 Answer

Where is the radiator fan switch located


FIRST THE RADIATOR FANN IS CONTROLLED BY A SENSOR AND IF NO HEAT IS COMING OUT BY FAN SPEED IT IS PROBALLY A BAD BLOWER MOTOR AND OR BAD RESISTOR FOR FAN SPEED

Jul 14, 2008 | Volvo 850 Cars & Trucks

Not finding what you are looking for?
Hunter 22460 52'' The Astoria Brushed Nickel Ceiling Fan Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hunter Dryers Experts

Fan Fair Of Boca
Fan Fair Of Boca

Level 3 Expert

1617 Answers

Paul Bade

Level 3 Expert

1398 Answers

yadayada
yadayada

Level 3 Expert

67757 Answers

Are you a Hunter Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...