Question about Briggs & Stratton Briggs Stratton Vanguard V - Twin Vertical Ohv Engine with Electric Start 23 Hp, 1" X 3 5/32" Shaft, ModelNo. 386777 - 0036 - E1

Open Question

What is the valve clearance on 23 horse brigs &straton intake & exhaust

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you check the valves on a 1993 onan 24 horse motor


MEASURE AND ADJUST VALVE CLEARANCE 1. Turn the flywheel clockwise until the intake valve opens and then closes. Continue turning flywheel until the TDC (top-dead-center) mark (A) on the flywheel is upward. Both valves (B) must be closed and the piston (C) must be at the top of its compression stroke. If the valves are open, the piston is on the exhaust stroke and the flywheel must be turned one revolution
2. Measure valve clearance using a feeler gauge. VALVE CLEARANCE SPECIFICATION Item Specification Intake Valve (A) . . . . . . . . . . . . . . . . . . . . . . . 0.13 mm (0.005 in.) Exhaust Valve (B) . . . . . . . . . . . . . . . . . . . . . . 0.33 mm (0.013 in.)
3. If necessary, hold tappet and turn tappet screw to adjust valve clearance
Below you will find a complete manual with illustrations to complete rebuild, ***PRESS THE HELPFUL BUTTON****
http://www.wfmfiles.com/download/manuals/CTM2_-_16_18_20_24_HP_Onan_Engines.pdf

Jan 20, 2016 | Garden

1 Answer

Valve adj. B&S gen. Model 030246 10 hp. OHV


Briggs and Stratton Valve Clearances

outdoorpowerinfo.com/engine_specs/briggs_valve_gaps.asp
Briggs & Stratton Intake and Exhaust Valve Clearances. Model Series, Engine Type, Intake Valve Clearance ( in. ) Exhaust Valve Clearance ( in. ).

Briggs and Stratton 10hp Generator Carburetor Repair ...

? 6:17
https://www.youtube.com/watch?v=O-fROtibEvE
Jun 5, 2010 - Uploaded by IFIXIT4U
In this video I will show you how to clean the carb on a Briggs10hp. This is a Nikki carb.

Nov 03, 2015 | Measuring Tools & Sensors

1 Answer

What is the valve adjustment spec on a brigs @ sttraton


There is no adjustment. The clearance is pre-set by the valve length and tappet length. If the valve seat is worn the clearance becomes non-existant. .020-0.30 clearance for both intake & exhaust will work okay.

Aug 21, 2014 | Garden

1 Answer

Torque specs. for a briggs @ stratton 24hp. head bolts


WHAT IS THE VALVE CLEARANCE ON A 23 HP. BRIGS MOTOR AND THE TORQUE ON THE HEAD BOLTS?

Jul 17, 2012 | Briggs & Stratton Briggs Stratton Vanguard...

2 Answers

Valve clearance 4g13


make the engine runs for about 30minutes before adjusting the valves,
valve clearances:
intake valve = 0.20mm(0.008 in)
exhaust valve = 0.25mm(0.010 in)
for reference only when the engine is cold,
valve clearances:
intake valve = 0.25mm(0.010 in)
exhaust valve = 0.30mm(0.012 in)
engine specs: mitsubishi 4g13 1.3L (if you have same engine)

Feb 29, 2012 | Mitsubishi Cars & Trucks

3 Answers

Valve clearance 4hj1 isuzu engine


This is the specs for the 4H Diesel engine:
Intake valves clearance cold 0.4mm(.016inches)
Exhaust valve clearance cold 0.4mm(.016inches)

Jan 28, 2011 | 1995 Isuzu Pickup

1 Answer

Intake valve & exhause clearance


3000 or 4000 is your clearance, get the piston up top dead center make sure piston is to the top of the cylinder rocker arms should be level with each other before you set them

Jun 05, 2010 | Swisher T14560 T - 60" Trailmower with 14...

1 Answer

I have a craftsman lt 1000 w/brigs&straton 17 horse engine i replaced battery & starter but the engine turns over slowly but wont start the battery is fully chaged Im a good mechanic but this has...


It sounds like the compression release is not working,it works by opening the exhaust valve during engine cranking.For the compression release to work the valves have to be adjusted,especially after the engine is broken in.Set the engine to top dead center on the compression stroke,the exhaust valve should be set to .004 and the intake to .002. I think you will find the exhaust valve is way too wide which is causing the hard crank problem.Set the valves by adjusting the nuts on the rocker arms,it should be a torx set screw located in the rocker arm.First back the torx screw out about a turn then hand tighten the rocker stud with the feeler gage in place then tighten the torx screw down to lock the setting.

Aug 05, 2009 | Craftsman Garden

Not finding what you are looking for?
Briggs & Stratton Briggs Stratton Vanguard V - Twin Vertical Ohv Engine with Electric Start 23 Hp, 1" X 3 5/32" Shaft, ModelNo. 386777 - 0036 - E1 Logo

Related Topics:

198 people viewed this question

Ask a Question

Usually answered in minutes!

Top Briggs & Stratton Tools & Hardware - Others Experts

Randy Schumann
Randy Schumann

Level 2 Expert

391 Answers

Bill Boyd

Level 3 Expert

42120 Answers

nirodacyar

Level 2 Expert

65 Answers

Are you a Briggs & Stratton Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...