Question about HP PSC 2210 All-In-One InkJet Printer

1 Answer

NO Power I have power from the cable but the printer will not turn on? it was fine and it just stopped?

Posted by on

  • Emilion May 22, 2008

    I have the same problem - the PSC2210 suddenly won't turn on although cord is attached properly etc. I also did diagnostics during an online chat with an HP technician; he ended up saying he didn't know what the issue was and that the best thing would probably be to get a new printer. Has anyone else had this issue and resolved it?

  • Anonymous May 27, 2008

    Printer has been working fine. I inserted a photo colour cartridge and the printer did an alignment and then turned itself off with the print carridge over to the left.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 27 Answers

Check the power module wether its warm or not.......if not then first you can try to change the walloutlet and still if there is no power then module needs to be changed.

else

if the module is warm then the power cable running fom the module to the printer needs to be changed.

If still there is no power then the printer needs to be replaced.

Posted on May 31, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wont turn on


did you check the usb cable try another cable if not check the power cord if it dose not turn on then you need a new one

Oct 29, 2013 | Lexmark X7350 All-In-One Printer

1 Answer

No power to printer


It can be your printer power cable problem..try to use another cable and let see what happen.....:))


If you need any technical help on printer then you can reach at http://www.vtechsquad.com/

Nov 16, 2012 | Epson Stylus Photo RX500 Printer

1 Answer

I bought new ink cartridges and when i try to print something it gives me a error number 5100


Cause: Head too hot, exceeds the threshold, usually the color Catridge
Solution:

1. Turn Off printer, cable power still plug in.

2. Press Stop/Reset button, don't release the button.

3. Press Power button by holding without release and than release Stop/Reset Button.

4. Press Stop/Reset button two times (2x) now release the Power Button.

5. Wait until service mode to zero (0).

6. Turn off the Printer, cable power still plug in.

7. Press Stop/Reset button, don't release it.

8. Press Power button don't release & than release Stop/Release button.

9. Press Stop/Reset button four times (4x), wait until service mode to "1"

10. Turn off printer, and loose cable power, wait for one (1) minute.

11. Connect cable power, turn on printer again, now this printer ready to use.

Aug 26, 2011 | Canon Pixma Mp250 Allinone Inkjet Photo...

1 Answer

P08 in LED indicators for CAnon pixma mp 258... how to solve please


To solve your problem follow the instruction step by step...

1. Turn Off printer, cable power still plug in.

2. Press Stop/Reset button, don't release the button.

3. Press Power button by holding without release and than release Stop/Reset Button.

4. Press Stop/Reset button two times (2x) now release the Power Button.

5. Wait until service mode to zero (0).

6. Turn off the Printer, cable power still plug in.

7. Press Stop/Reset button, don't release it.

8. Press Power button don't release & than release Stop/Release button.

9. Press Stop/Reset button four times (4x), wait until service mode to "1"

10. Turn off printer, and loose cable power, wait for one (1) minute.
Connect cable power, turn on printer again, now this printer ready to use

Aug 23, 2011 | Canon Pixma Mp250 Allinone Inkjet Photo...

2 Answers

Error 5200 of canon pixma mx328. i already tried turning it on and off several times and even got the cartridges and returned them back but still when i tried to print a page error 5200 still...


Error no 5200 is caused by its temperature high.. to solve your problem follow the instruction given below::

1. Turn Off printer, cable power still plug in.

2. Press Stop/Reset button, don't release the button.

3. Press Power button by holding without release and than release Stop/Reset Button.

4. Press Stop/Reset button two times (2x) now release the Power Button.

5. Wait until service mode to zero (0).

6. Turn off the Printer, cable power still plug in.

7. Press Stop/Reset button, don't release it.

8. Press Power button don't release & than release Stop/Release button.

9. Press Stop/Reset button four times (4x), wait until service mode to "1"

10. Turn off printer, and loose cable power, wait for one (1) minute.

11. Connect cable power, turn on printer again, now this printer ready to use.

Aug 23, 2011 | Canon MX300 Office All-In-One Printer

1 Answer

I have Canon MP250 series I have a cde on led P 0 8


To solve your printer problem using the following directions..

Follow this instruction step by step.

1. Turn Off printer, cable power still plug in.

2. Press Stop/Reset button, don't release the button.

3. Press Power button by holding without release and than release Stop/Reset Button.

4. Press Stop/Reset button two times (2x) now release the Power Button.

5. Wait until service mode to zero (0).

6. Turn off the Printer, cable power still plug in.

7. Press Stop/Reset button, don't release it.

8. Press Power button don't release & than release Stop/Release button.

9. Press Stop/Reset button four times (4x), wait until service mode to "1"

10. Turn off printer, and loose cable power, wait for one (1) minute.

11. Connect cable power, turn on printer again, now this printer ready to use.

Aug 15, 2011 | Canon Pixma Mp250 Allinone Inkjet Photo...

1 Answer

Error 5200 or PO8?


1. Turn Off printer, cable power still plug in.

2. Press Stop/Reset button, don't release the button.

3. Press Power button by holding without release and than release Stop/Reset Button.

4. Press Stop/Reset button two times (2x) now release the Power Button.

5. Wait until service mode to zero (0).

6. Turn off the Printer, cable power still plug in.

7. Press Stop/Reset button, don't release it.

8. Press Power button don't release & than release Stop/Release button.

9. Press Stop/Reset button four times (4x), wait until service mode to "1"

10. Turn off printer, and loose cable power, wait for one (1) minute.

11. Connect cable power, turn on printer again, now this printer ready to use.

Aug 12, 2011 | Canon Pixma Mp250 Allinone Inkjet Photo...

1 Answer

Printer shows alarm with p and 8 flashing


Follow this instruction step by step.

1. Turn Off printer, cable power still plug in.

2. Press Stop/Reset button, don't release the button.

3. Press Power button by holding without release and than release Stop/Reset Button.

4. Press Stop/Reset button two times (2x) now release the Power Button.

5. Wait until service mode to zero (0).

6. Turn off the Printer, cable power still plug in.

7. Press Stop/Reset button, don't release it.

8. Press Power button don't release & than release Stop/Release button.

9. Press Stop/Reset button four times (4x), wait until service mode to "1"

10. Turn off printer, and loose cable power, wait for one (1) minute.

11. Connect cable power, turn on printer again, now this printer ready to use.

Aug 06, 2011 | Canon Pixma Mp250 Allinone Inkjet Photo...

3 Answers

My mp250 printer shows error p08, I can't use it in any way. I replaced the black ink tank with a new one and tried resetting the printer and it doesn't solve the problem.


Follow the instructions step by step

  1. Turn off printer, cable power still plug in,
  2. Press Stop/Reset button don't release
  3. Press Power Button don't release and than release Stop/Reset button
  4. Press Stop/Reset button 2X , wait until service mode to " 0 "
  5. Turn off printer, cable power still plug in
  6. Press Stop/Reset button don't release
  7. Press Power Button don't release and than release Stop/Reset button
  8. Press Stop/Reset button 4X , wait until service mode to " 1 "
  9. Turn off printer, and loose cable power, wait one minute.
  10. Connect cable power, turn on printer again, now this printer ready to use.

Jul 06, 2011 | Canon Pixma Mp250 Allinone Inkjet Photo...

2 Answers

HP Officejet 5610 stopped printing


Hi,
turn the printer on and unplug the power cable from the back of the printer without turning the power off
press and hold :
OK and CANCEL, while keeping them on hold put the power cable back in ... it ll do a full NVRAM reset on it .. then it ll prompt u for the language and country follow the steps it ll be resolved ...
Best of luck
:-)

Jun 02, 2008 | HP Officejet 5610 All-In-One InkJet...

Not finding what you are looking for?
HP PSC 2210 All-In-One InkJet Printer Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Printers & Copiers Experts

kakima

Level 3 Expert

96372 Answers

k24674

Level 3 Expert

7987 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a HP Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...