Winder has come off - Watches

Looks like you put it into a $3,000 winder!

How to put watch in Wolf Winder?
To put your watch in the winder, remove the cuff by pinching the two outside wings inward and pull. Close your watch's strap or bracelet before placing the watch on the cuff. Compress the cuff, then slide your watch over the cuff, the watch face should cover the WOLF logo.

Help - Winders ' WOLF - Wolf 1834

https://www.wolf1834.com > faq > winder-faqs Search for: How to put watch in Wolf Winder?

More and videos

https://www.google.com/search?q=How+to+wind+a+Wolf+Agney+watch&rlz=1C1QJDB_enCA643CA644&oq=How+to+wind+a+Wolf+Agney+watch&aqs=chrome..69i57&sourceid=chrome&ie=UTF-8

You have selected a wonderful watch... Heuer and TAG/Heuer should be gently wound by the motion of the human wrist and the falling of a centrally pivoting weight (there is no ideal direction).

AUTO-WIND function is NOT at all unique to your watch...

After a couple of CHEAPER "winders" failed me... and after I figured about 4 watches was more than enough to keep wound... I found the greatest BASIC watch winder... to run year over year (efficiently and quietly)

MTE watch winder (their very basic WTS-4).

Good luck: I WILL try to include the URL (see page 6)

http://mte-watchwinder.com/fileadmin/PDF-Uhrenbeweger/MTE_Watch_Winder_Brochure_Engl.__09-2015.pdf

Watch Winder Setting & Instructions for Executive Collection

Jared Tracy
posted this on March 30, 2012, 2:44 PM

• inShare
There are four modes for our Executive Collection of Watch Winders (TM and SM series):

Mode 1 (both switches with the O pressed in): rotates for 180 seconds on then 12 minutes off.
Mode 2 (first switch with the O pressed in, second switch with the I pressed in): rotates 180 second on then 15 minutes off.
Mode 3 (first switch with the I pressed in, second switch with the O pressed in): rotates 180 seconds on then 18 minutes off, then 180 seconds in the opposite direction.
Mode 4 (both switches with the I pressed in): rotates 180 seconds on then 24 minutes off.

For switching winding direction:
I pressed in will wind clockwise
II pressed in will wind counter clockwise
Neither pressed in will turn the winder off

*Please note that the CW and CCW settings do not apply when the winder is set to Mode 3 as this mode winds in both directions.

sorry don't understand what your problem is

How do you repair motors on steinhauser watch winder

Pull out winder 1 step and us the push buttons to adjust hands to 12 o.clock . when you have done this pull winder right out and use push buttons to set other hands then push winder back in.

Some winders need to be unscrewed (its a water resistance feature).

Try turning the winder anticlockwise about a quarter of a turn or so.

(Don't forget to screw it back in when you have finished!)

The watch should last 36 hours from fully wound. If your wearing the watch and using a watch winder and its still stopping, you have a problem with the mechanism. Get it serviced. (its probably just a clean and oil req'd) 

Yes, but for an authentic Jaeger-lecoultre watch it will be very expensive.

I have a Fossil Speedway watch (FS2895). The second hand was on the 2, and I wanted it on the 12. Like the above suggestion says, pull out the winder twice as if you are going to reset the time. However, leave the winder alone after that and, instead, press and hold the chronograph start/stop button (above the winder) until the second hand reaches the desired position. If you want to move the hand a small bit at a time, just press and release that same button until the hand reaches the desired position.