Question about Toshiba 32A43 32" TV

1 Answer

Power light just blinks

Cable Co. came and installed new wire in home and replaced boxes. Now the TV just blinks red, I have unplugged it for as long as two days. It was working fine till the new box was installed. When I run the RF wire to another tv I get a good Picture.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,224 Answers

Can you get a signal without box to tv
everythings going hd these days it could be they have it set for an hd
rf's pull there signal from the air and and filters to wear its supposed to go
hd is direct signals
9 times out of 10 the new box in not compatible with tv
or the guy who came in and installed the box did something to your tv and ran away

Posted on May 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WE are trying to hook up our new cable box. We cannot get the TV to go on. A red light keeps flashing.


What brand and model is the t.v.? Usually a red blinking light is a code meaning something is wrong. Watch how many times it blinks and post the brand and model of the t.v. and how many times the stand by light blinks. First unplug it for at least 2 minutes and re-check all the cable connections to make sure they are plugged into the right places. Then plug the t.v. back in and turn it on first before you turn the cable box on. Good Luck, hope this helps.

Jul 31, 2011 | Memorex Standard (CRT) Televisions

1 Answer

Tv turns off on its own. power light now blinking red, tv not on


Unplug,replug,push the popwer buton couples time,see if stable green LED light,should get tv pic& suond back, not replaced the backlight video board it some how die.

Nov 26, 2009 | Standard (CRT) Televisions

1 Answer

Blinking red led light


The TV is on protect mode.

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

Also ensure that the fault is not coming from a faulty receiver box sending bad signal, check if you get same problem with no receiver box or dvd connected.

If that does not work, and you keep having a flashing led on front of the TV, and tv turning off by itself after a while, that indicates a fault condition.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible reasons.

1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.

2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , startingthe flashing light.


If you are in situation one, then theTV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

Common faults that can occur are a blown capacitor on power board, a convergence IC has blown, or a fault on Digital board.

Check also the video cable or any external connection cable, if the cable is shorting, or the connector is bad, you can get same flashing state because of the video cable.


If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

May 19, 2009 | Philips 34PW9846 34" TV

1 Answer

BUSH LCD 27 inch


The TV is on protect mode.

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

Also ensure that the fault is not coming from a faulty receiver box sending bad signal, check if you get same problem with no receiver box or dvd connected.

If that does not work, and you keep having a flashing led on front of the TV, and tv turning off by itself after a while, that indicates a fault condition.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible reasons.

1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.

2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , startingthe flashing light.


If you are in situation one, then theTV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

Common faults that can occur are a blown capacitor on power board, a convergence IC has blown, or a fault on Digital board.

Check also the video cable or any external connection cable, if the cable is shorting, or the connector is bad, you can get same flashing state because of the video cable.


If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

Jan 23, 2009 | Bush 5693D 24" TV

1 Answer

Blinking red light no picture or sound


The TV is on protect mode.

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

Also ensure that the fault is not coming from a faulty receiver box sending bad signal, check if you get same problem with no receiver box or dvd connected.

If that does not work, and you keep having a flashing led on front of the TV, and tv turning off by itself after a while, that indicates a fault condition.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible reasons.

1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.

2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , startingthe flashing light.


If you are in situation one, then theTV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

Common faults that can occur are a blown capacitor on power board, a convergence IC has blown, or a fault on Digital board.

Check also the video cable or any external connection cable, if the cable is shorting, or the connector is bad, you can get same flashing state because of the video cable.


If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

Jul 18, 2008 | Toshiba 36A43 36" TV

1 Answer

Power button Flashes


For the first one, please list the model number and count the blinks. Also, can you please post each problem separately. It will get too confusing trying to address 3 sets with different but similar problems.
Thanks,
Dan

Mar 18, 2008 | Standard (CRT) Televisions

2 Answers

Black screen


my sony kp-61hs30 displays that there is no siginal, also the red indicator light blinks when the power is turned on but goes out i have dirct cable pluged into the set and up until about a week ago it worked fine.All of the other tv's in my home work fine so i don't understand what the problem is . I have a dvd player connected to the set and it works great for viewing dvd's please assist with me with some trouble shooting points

Jan 24, 2008 | Sony KP-61HS30 TV

2 Answers

After power outage, tv doesn't turn on


First, the blinking light is a code, how many blinks? Second, regulators are not resettable. Don

Aug 17, 2007 | Panasonic CT-36HL43 36" TV

2 Answers

Tv will not light up.


I do not have expertise in cable TV systems. A power failure when you have the TV connected to a system which is normally always on or on standby may need resetting if interrupted. Try the TV on an aerial or with its scart input, but disconnected from the cable unit. The blinking red light indicates a fault

Oct 15, 2006 | Sony KV-32S26 32" TV

Not finding what you are looking for?
Toshiba 32A43 32" TV Logo

Related Topics:

142 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toshiba Standard (CRT) Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

 Elex
Elex

Level 2 Expert

49 Answers

Cindy Wells

Level 3 Expert

4759 Answers

Are you a Toshiba Standard (CRT) Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...