Question about Behringer POWERED MIXER, 20 CH, 400 WTS AMPLIFIER => Model PMX5000 Car Audio Amplifier

Open Question

Europower pmx 1000 mixer, problem is power supply i need a schematic circuit

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5603 Answers

SOURCE: BEHRINGER EUROPOWER pmx 1000

The voice cancellor switch basically subtracts the left and right signal because the vocalist is usually centered... The noise would likely be in an op amp associated with this feature...

Compare your circuit to a PMH1000. On that unit first thing to check is the two electrolytic caps at the left and right noise cancellor outputs.

There are a wholle bunch of resistors and IC's 48,50,37 are all involved.

Troubleshoot this one with freeze mist (ccircuit cooler). The problem should show up easily by heating and cooling.

Posted on Jun 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i hook up my laptop and my tablet to a behringer Europower PMX 2000


Easy to do - just get a patch cord that has a stereo 1/8" plug on one end and two phono (RCA) plugs on the other end. Plug the phono plugs into the "Tape IN" jacks on the mixer and use the "Tape" volume to adjust the sound level. It's best to turn your laptop or tablet volume up to maximum, then adjust the volume on the mixer.

Jan 15, 2015 | Behringer Audio Players & Recorders

1 Answer

Need the schematic print for PMP 4000.


You can find it on the Web. Patience and some searching...?

Jun 03, 2014 | Behringer Pmp4000 Europower 1600-watt...

1 Answer

My europower pmp 2000 powered mixer wont turn on and the fuse appears good. I turned it on and it immediately turned off ,nothing smells burnt. any ideas on what it could be


This is likely a power supply failure, possibly brought on by a failure of one of the amp channels.

This is probably close to your supply:

http://elektrotanya.com/behringer_sps600_power-supply_sch.pdf/download.html

Scroll down to "get manual" and click on that to download schematic. Ignore other download links.

Aug 05, 2011 | Behringer Pmp2000 Europower 800w 10ch...

1 Answer

There are two resistors 310-3 10R on the power supply of the Europower pmp 5000, i need to know if it is 330k or 330om.


The schematic for the power supply does NOT show resistors in the 310-3... Where are these in the circuit... IF THESE happen to be the gate drive resistors for the IGBT's they are 33 ohms. If you have hasd a failure in this area there are other parts that typically get destroyed, including one or both the speedup diodes at the same gates; Here is the complete PMP5000 schematic:

http://elektrotanya.com/behringer_europower-p0569_hca2400_sps1000_dpx_pmp-1280s_5000_sch.pdf/download.html

Scroll down to "get manual" and cliick to download. IGNORE other download links. If you need help restoring the PSU get back to me.

Jul 20, 2011 | Behringer Europower Pmp5000 Powered Mixer...

1 Answer

My mixer stopped working out of the blue no power want turn on anything ??????????????


Power supply probably failed. This is not a DIY for the inexperienced.

This will be close to your schematic: http://elektrotanya.com/behringer_pmh1000.pdf/download.html

Scroll down to "get manual" and click to download. IGNORE other download links.

Jul 19, 2011 | Behringer Europower Pmp1000 Powered Mixer...

1 Answer

Hello! I have a Behringer EUROPOWER PMH 1000. But the power board burnt source. What do I will acquire another, or fixable?


Often teh power supply fails because of other problems. Unless the board has flame damage the parts that are defective can be replaced... Getting some of the parts that are special can take time. Most of the components are available at many sources however. The SPS400 power supply can be repaired.

Here is link to schematic that should have the SPS400 as well as the rest of the PMH1000 on it.

http://elektrotanya.com/behringer_pmh1000.pdf/download.html

Jan 18, 2011 | Behringer XENYX 2442FX Mixer

1 Answer

Behringer pmx 2000 missing knob


If the shaft broke, then you will have to replace the whole encoder for it. You cannot glue a shaft and expect it to hold.

Mar 17, 2009 | Behringer POWERED MIXER, 20 CH, 400 WTS...

1 Answer

BEHRINGER EUROPOWER pmx 1000


The voice cancellor switch basically subtracts the left and right signal because the vocalist is usually centered... The noise would likely be in an op amp associated with this feature...

Compare your circuit to a PMH1000. On that unit first thing to check is the two electrolytic caps at the left and right noise cancellor outputs.

There are a wholle bunch of resistors and IC's 48,50,37 are all involved.

Troubleshoot this one with freeze mist (ccircuit cooler). The problem should show up easily by heating and cooling.

Oct 29, 2008 | Behringer POWERED MIXER, 20 CH, 400 WTS...

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

399 people viewed this question

Ask a Question

Usually answered in minutes!

Top Behringer Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4834 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

The Knight
The Knight

Level 3 Expert

73647 Answers

Are you a Behringer Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...