Question about Insignia Digital-to-Analog Converter for Analog TVs

1 Answer

Converter boxes I have coupons for them, do you have the box to convert old tv to digital? Can I call and order from Best Buy? urolemah

Posted by on

1 Answer

You can pick the box up at your local Best Buy

Posted on May 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

All ready used box once. Now going back to antenna. Not receiving display or menu on T.V. screen.


All TV over the air is transmitted as a digital signal now. In order to see it on an older TV (read Analog), you must have a signal that you can receive(antenna hook up) and a digital to analog converter box. That box allows you to see your digital signal on older TVs. The signal is sent from the antenna to the box via a RF connection, and decoded to channel 3 or 4 (your choice). for further information see Consumer Report at:

http://www.consumerreports.org/cro/electronics-computers/tvs-services/non-digital-tvs/digital-converter-boxes/digital-tv-converter-boxes-first-look-3-08/overview/digital-tv-converter-boxes-first-look.htm

Jan 09, 2011 | Insignia Digital-to-Analog Converter for...

2 Answers

I bought the magnavox and all my channels are


Check the converter box. Many have a volume setting that is usually set very low at the factory. On the remote control for the converter check to see if there are volume buttons. If so, change the converter box volume higher, to a level that makes the TV audio level "normal", then use the volume control on the TV for adjustment as you watch. If you set the volume on the converter box too high, you may get some distortion in the audio from your TV. So adjust the converter box to find the proper output from your TV without distortion.

Jun 20, 2009 | Insignia Digital-to-Analog Converter for...

1 Answer

Will a universal remote work on a insignia digital converter box?


doublecheck the paperwork for both the converter box and the universal remote. the universal may be too old to be used with your converter. look in the back of the universal's manual to see if your box's corporation has a code you can set.

Jun 12, 2009 | JVC TH-C4 System

1 Answer

Converter box connection


You need to get a 75-ohm to 300-ohm transformer, also called a "balun". Radio Shack sells them and you may also be able to find them at retailers who sell TV antennas. It's a small cylinder with a threaded connector at one end for the cable from the converter, and a flat wire with two terminals for the TV connection. Connect the terminals under the "VHF" screws on the TV, put the set on channel 3 or 4 depending on your converter box setting (most are on 3 out of the box) and you're good to go. On a set of that age, you might need to tinker with the fine tuning adjustment a little for the best picture from the converter box.

May 04, 2009 | Insignia Digital-to-Analog Converter for...

1 Answer

Digital tv antenna reception


try googling how to build an antenna with coat hangers. not pretty but cheap!

Apr 08, 2009 | Insignia Digital-to-Analog Converter for...

1 Answer

Hooking actual live coaxial from Cable Co. to Insignia Converter Box ...


Based on the specs that I have read I am going to say you cannot hook up cable to the converter. Best thing to do would be to call cable company that provides service there and see if it was turned off on the billing side they probably just didn't come out and disconnect from the pole. That might give you service but missing some features such as tv guide channel. Now some tv's have tv guide built into them and maybe in the move that feature on the tv was turned off it they were using it that way before. Here is what the specs say about that converter:

Use this digital-to-analog converter to convert digital TV broadcast signals to analog signals on analog TVs with antenna-based reception.

Nov 08, 2008 | Insignia Digital-to-Analog Converter for...

3 Answers

Connect tv vcr and dvd player to digital converter box


Yes you can first connect the converter box to the antenna first. Next hook the tv out on converter box to vcr in on vcr. Next hook the vcr out to the tv in and watch vcr and converter box on channel 3 sometimes channel 4.on the actual tv and of course change channels with converter box remote. For dvd player hook it straight to tv with red,white,and yellow cables that come with your dvd player. Then to watch dvd player if it's hooked up that way you have to put your tv on a input like video 1 or input 1. This can be done by using the tv remote and looking for a button that says tv/video or input or source button. This is some common names for that button on tv remotes.

Nov 02, 2008 | Insignia Digital-to-Analog Converter for...

1 Answer

Insignia NS-DXA1 - Digital to Analog converter box


I have had my converter box 5 days now. I hooked it up to the TV and set it up. No Problem. Except there are no instructions on how to set up the VCR/DVD player with it, which we use more than we do watching TV. Everything worked fine until on the second day we had it I read I could program the remote to turn the TV on and off. I followed the instructions and the TV went off. When I turned it back on, my remote went berserk. If I try to change a channel it will quickly flip through all the channels until I turn the converter box off. Same with the volume, it goes up and down, up and down until I shut off the box. The remote does not work unless you are about 1 foot away from the box. And the remote has never turned the TV on or off except that first time I programed it.

May 19, 2008 | Insignia Digital-to-Analog Converter for...

8 Answers

How to connect my dvd & vcr with the converter box


Here is my setup.
1) Separate DVD player 2) Separate VCR 3) Digital to Analog Converter box 4) Analog TV 5) Rabbit ears (UHF/VHF) antenna
The antenna goes into the converter box.   The RF-output of the converter goes into the RF-Input of the VCR The DVD output goes into the front input jacks of the VCR The VCR RF-output goes into the TV RF-Input The VCR Line output goes into the front of the TV
To watch DVDs, we turn on the DVD player, turn on the VCR, and set the VCR channel to L2, and tune the TV to channel 3.  The converter is off.
To auto record on the VCR, the converter must be tuned to the station being recorded.  The converted must be turned on, the TV can be off. 
To watch VCR tapes, turn the TV and VCR on.  The TV is set to channel 3.  Just press play on the VCR.
To Watch TV.   Turn the TV and converter on.  The TV is set to channel 3.   Change the stations using the converter.  

May 06, 2008 | Insignia Digital-to-Analog Converter for...

Not finding what you are looking for?
Insignia Digital-to-Analog Converter for Analog TVs Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Insignia Home Theater Systems Experts

Brandon M.

Level 1 Expert

34 Answers

Cindy Wells

Level 3 Expert

4754 Answers

Stephan Reichert
Stephan Reichert

Level 2 Expert

194 Answers

Are you an Insignia Home Theater System Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...