Question about HP Color LaserJet 2600n Printer

1 Answer

Changing the fuser unit

I would like to change the fuser unit on my printer and i have a problem with getting about to finally open the printer and change the fuser unit.

Your help will most be appreciated.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 300 Answers

1 Unplug the power cable.
2 Remove the paper delivery tray assembly
3 Remove two (2) screws from the right cover assembly
4 Remove the right cover assembly, carefully disengaging the catches
5 Unplug the control panel cable.
6 Insert a screwdriver to loosen the release tab on each side of the upper face cover
7 Remove the upper face cover
8 Remove four (4) screws from the upper cover
9 Lift up and remove the face-down cover
10 Remove the output tray by releasing the tabs.
11 Unplug the harness from the fuser motor
12 Open two (2) clips and remove one (1) clip to remove the fuser connector.
13 Unplug two (2) 3-pin optical encoder wires
14 Unplug the red high-voltage bias wire.
15 Remove the thermistor wire.
16 Remove the cables from the wiring harness.
17 Remove three (3) screws from the fuser chassis.
18 Gently rocking if necessary, roll the fuser forward to remove.
Use the following procedure to replace the fuser.
1 Align the fuser tabs with their respective holes.
2 Complete replacement by following steps 1 through 18 above in reverse order.
NOTE When replacing the right cover, align the tabs on the upper edge of the right cover
and lower edge of the face-down cover with their respective slots.
Hope this helps

Posted on May 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fuser chnge


1. remove the cover for the duplexing drawer below the fuser drawer.
2. extend the fuser drawer
3. remove the 3 front covers of the fuser drawer
4. remove the three black screws that secure fuser motor,
5. remove the yellow cover to access then two screws that secure the fuser unit to the drawer.
6. unplug the connectors you see in front and the one below the fuser unit.
7. fully extend the drawer and push in the leaf springs you see and pull the drawer out further
8. remove the two screws you see on the top of the fuser and remove the fuser unit- gently.
Good luck

Jul 11, 2014 | Canon LASER SHOT LBP 3300 Printer

1 Answer

We have a Brother MFC-9840CDW with a fuser that's needing to be replaced. Brother says the fuser is part that "is not recommended to be done by the consumer." Are their hazards for changing...


The fuser can be replaced by opening the back cover and removing 2 screws.


http://www.precisionroller.com/fuser-assemblies---units-for-brother-mfc9840cdw/products.html


joed911_10.jpg

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response

Thanks, Joe

May 20, 2011 | Printers & Copiers

1 Answer

There is a warning said : " fuser unit end". What is the problem for that printer HL-4040CN? Even after I changed the drum unit and belt unit, there are still 2 warnings appearing to ask for...


first you are talking about the FUSER END message that means you have to change the FUSER and as for the DRUM and BELT you have to RESET the TIMER to tell the printer that it has been changed as well as for the FUSER those are consumable parts they have a life and the printer is programed to tell you to change them after so much copies.

Good luck!

Jan 05, 2011 | Brother HL-4040CN Laser Printer

1 Answer

1300 Printer prints roller marks only on one side. have tried cleaning roller & changing cartridge.


If it is not the cartridge check the fuser. Open the back access cover shine a light in and look for wear marks on the grey fuser film. If it is worn the fuser film is worn it should be replaced.

Jun 09, 2010 | HP LaserJet 1300 Printer

3 Answers

Papr jam in fuser unit C900


You can download (free) the Service Manual for the C900/C1900 here;
http://tinyurl.com/2dxyzrr It contains comprehensive dis-assembly, re-assembly and service instructions including parts lists and wiring diagrammes. The download is in six zipped parts. After downloading all of them unzip part 1 and it will rebuild the complete file as a pdf document.
This printer uses the same print engine as the Minolta QMS/Konica Minolta Magicolor 2300/2350 printers. KM versions of the manual are also available from the above site. Much of the content is virtually identical but the instructions are not quite as comprehensive or as detailed as the Epson version. KM MC2300/2350 users may want to download both versions.

Geo.

May 02, 2010 | Epson AcuLaser C900 Printer

1 Answer

Verticle lines printing on laser printer


Check the fuser. If it is the fuser, you should be seeing 3 dark lines on the fuser film. Here is the picture about how the film looks like:
d0e1b68.jpg

Changing the film usually solve the problem. However changing the film itself is difficult. You have to remove and basically disasseble the fuser, and change the film. However it is fairly cheap and if you decide you would like to save some money, here is the link available in ebay:
http://cgi.ebay.com/Fuser-Film-Sleeve-HP-LaserJet-P3005-RM1-3740-/250558576965?cmd=ViewItem&pt=BI_Toner&hash=item3a56747945


Or, simply search for 'P3005 Fuser Film' and you will find a lot.

Other than that, you can change the entire fuser. Please note that fuser for P3005 is not consumer installable part. You still have to take out some parts in order to change the fuser.

The parts are available from many parts supplier. Simply google 'P3005 fuser'. Usually around $100 for a refurbished fuser.

You can also recycle your old fuser and get some moeny! (about $15-$25 per fuser).

Good luck!

Apr 09, 2010 | HP LaserJet P3005n Printer

4 Answers

We have put a new toner in but still we are experiencing lots of horizontal lines??


Check the fuser. If it is the fuser, you should be seeing 3 dark lines on the fuser film. Here is the picture about how the film looks like:
d0e1b68.jpg

Changing the film usually solve the problem. However changing the film itself is difficult. You have to remove and basically disasseble the fuser, and change the film. However it is fairly cheap and if you decide you would like to save some money, here is the link available in ebay:
http://cgi.ebay.com/Fuser-Film-Sleeve-HP-LaserJet-P3005-RM1-3740-/250558576965?cmd=ViewItem&pt=BI_Toner&hash=item3a56747945


Or, simply search for 'P3005 Fuser Film' and you will find a lot.

Other than that, you can change the entire fuser. Please note that fuser for P3005 is not consumer installable part. You still have to take out some parts in order to change the fuser.

The parts are available from many parts supplier. Simply google 'P3005 fuser'. Usually around $100 for a refurbished fuser.

You can also recycle your old fuser and get some moeny! (about $15-$25 per fuser).

Good luck!

Nov 17, 2009 | HP LaserJet P3005n Printer

3 Answers

Jam 01-009 code from my Samsung SCX-6345. It always jam at the fuser unit please help.. thanks..


Probably have a scrap paper stuck in the fuser or a "stripper finger" out of place, catching the paper. You'll need to remove the fuser to get a good look at things.

Aug 04, 2009 | Samsung SCX-6345N Laser Printer

Not finding what you are looking for?
HP Color LaserJet 2600n Printer Logo

729 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Printers & Copiers Experts

kakima

Level 3 Expert

96333 Answers

k24674

Level 3 Expert

7987 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a HP Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...