Question about Dewalt 18 Volt Xrp Heavy Duty Hammer Drill Kit

1 Answer

How do you remove the keyless chuck - Dewalt 18 Volt Xrp Heavy Duty Hammer Drill Kit

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 490 Answers

There is a screw in the bottom of the inside of the chuck. You have to loosen it with a quick, sudden turn while keeping pressure( as the chuck wants to turn with it). Putting the drill in its slowest gear helps increase resistance some.

Bit of a nuisance, really but what can you do:)
Regards, Farmerbear at FixYa.com

Posted on Sep 14, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Require a 10mm and a 13mm Male-fitting Keyless Chucks


I suggest that you do not proceed, Keyless chucks can be problematic especially if dust /debris from material being drilled gets into the chuck. I have had to remove the Keyless chuck from my B&D drill and replace it with a keyed chuck- no problems since.

Apr 04, 2017 | Drills

2 Answers

How can I replace the keyless chuck on my Dewalt DWD215G?


Open the chuck wide open. In the center is a retaining screw, they usually have left hand threads. Remove the screw. Take an allen wrench1/4" to 3/8" in size and fasten the short side tightly in the chuck. The chucks are usually right hand thread, so take a small hammer and strike the allen wrench to turn the chuck to the left to loosen it. Once you have the chuck off, verify the thread size of the drill motor shaft, then go to McMaster-Carr and choose the one you need.

Apr 16, 2011 | Dewalt DWD215G 12Inch 10AMP Heavy Duty Mid...

1 Answer

I can not change the drill bit. Do I need another tool?


that depends on whether or not you have a keyed or keyless chuck. if you have a keyless chuck then you do not need another tool you must turn the chuck counter clockwise to loosen the chuck and replace the bit. if you have a keyed chuck then you will see three holes around the chuck of the drill ie the part that holds the bit. just below the holes you will see teeth spaced evenly around the drill. a chuck key allows you to put the end of the key in one of the holes and using the teeth you turn the chuck key thereby loosening the chuck and allowing you to change the bit. if you have a keyed chuck just take it to your local hardware store and they can provide you with the correct key and show you how to remove the bit. if your chuck is keyless the hold the chuck put the drill in reverse and pull the trigger use a glove to protect your hand

Feb 24, 2011 | Drills

1 Answer

How do I remove the Chuck from my Mikida 9.6 volt keyless drill


Dont know about a Makita, but my Craftsman drill , if you open the chuck all the way and look inside the hole where the bit goes, there;s a screw there that you can use to remove the chuck. amybe yours is the same way.

Nov 23, 2010 | Makita Keyless Drill Chuck Set, HP1501...

2 Answers

Remove keyless chuck on a 12 volt makita drill


There should be a Screw in side the end of the chuck were u put the drill bit in u will have to undo it back wards its got a left hand thread

Oct 23, 2009 | Makita 12 Volt Cordless Drill/Driver Kit

1 Answer

Need to change a keyless chuck


open jaws for large size bit.look in bottom and there will be a screw slot or phillips head screw or possibly an allen head screw.remove this,by possibly turning clockwise. and then chuck up a large allen wrench. try removing the chuck by tapping wrench with hammer. this may be threaded on counterclockwise.have to try both ways.

Aug 28, 2009 | Craftsman 19.2v 3/8"drill/driver W/ Work...

1 Answer

Keyless chuck removal


Yes you can use any kind if chuck as long as the thread that attachs it is the same size, look on line lots of tool stores sell them cheap.

Sep 22, 2008 | Makita HP1621FK 5/8" Hammer Drill Kit with...

1 Answer

Drill chuck swap


1. Turn the screw clockwise to take it out.
2. Then you needs 3/8 allen key & insert the short side of the allen key & tighten the chuck.
3. hold the drill at the edge of the table & wack the allen key
counter clockwise & do it again as needed.
4. dewalt keyless chuck will fit but you might add a washer to insure the chuck is not rubbing the clutch collar.
5. putting it back together the other way.

Jun 01, 2008 | Dewalt DC920KA Heavy Duty Xrp 18V Cordless...

Not finding what you are looking for?
Dewalt 18 Volt Xrp Heavy Duty Hammer Drill Kit Logo

206 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dewalt Drills Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Jim Thurston

Level 3 Expert

670 Answers

Are you a Dewalt Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...