Question about Ovens

3 Answers

WHIRLPOOL DOUBLE WALL OVEN GETTING A E1-F5 CODE

According to the manual, E1-F5 says to replace the Latch Assy. We replaced the latch, and the same error code is coming back again per the customer. Is there anything else it could be, or did we get a faulty part.
Can you advise.

Thank you, Cheryl

Posted by on

  • 1 more comment 
  • debaird Nov 18, 2008

    Whirlpool Super Capacity 465 Electric. Model RF366PXGT2.

    Oven works normally, but tried to start cleaning cycle. After about 30 seconds the E1-F5 code begins flashing and the unit begins beeping.

    Suggestions?

  • Anonymous Dec 09, 2008

    My stove is a 465 Whirlpool. It just starts flashing F5 and E1 and beeping. What could be the problem?

  • Anonymous Mar 18, 2014

    kitchenaid double oven door locked error code F5 E1

×

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.
    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Thanks tech17. I did get it to work. I had jostled it some before but applied a bit more muscle and it started making some noise and then latched.


Posted on Nov 20, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.
    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I had the same problem.  However, after I pushed the oven door hard until it says "Locked" on the screen, the self-cleaning started just fine.  The door was not properly closed, in my case.

Posted on Nov 20, 2008

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points
    All-Star:

    An expert that got 10 achievements.
    MVP:

    An expert that got 5 achievements.
    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,314 Answers

If the door switch is bad the eoc will think its a latch failure there are two parts to the door switch 1 tells the eoc the door is shut one tells the light to turn own

Posted on May 16, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

6ya.com

6ya - Get Instant Help

6ya.com

Need repair answers fast Use 6ya to...

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a whirlpool accubake self cleaning oven.. when trying to use the self clean option it now states e1 f5 in the digital screen what do i do know?
Most commonly that is a runaway temperature error which usually means the temperature probe is bad and needs to be replaced. If you need more detailed instruction or help making this repair visit the link below:
Appliance Repair Help With Live Chat

Mar 26, 2017 | Whirlpool Ovens

Tip

Whirlpool oven, stove and range fault codes (ERC and EOC display errors).
Here a list of Whirpool oven fault codes. The codes had been collected from different service manuals. This was a memo that I wrote for my own use. I think this can be useful to owners and technicians.

WHIRLPOOL - most models
Range/Stove and Oven Fault Codes, Common error codes.

F1 - Analog control board Failure
Disconnect for one minute - if error comes back, replace control board
F1 - Shorted control keypad
Replace keypad
F3 - Oven temperature sensor open
Replace oven temperature probe
F2 - Oven temperature sensor shorted
Replace oven temperature probe
F3 - Oven too hot
Replace oven temperature probe
F3 - Clean temperature too hot
Replace oven probe
F5 - Door latch switch fault
Test and replace the door switch.


Whirlpool with 4 Digit Failure Code:

F1 - E1 - Electronic control (flip flop)
Replace control board
F2 - E0 - Shorted control keypad
Replace keypad
F3 - E0 - Oven temperature probe open
Replace temperature probe
F3 - E1 - Oven temperature probe shorted
Replace temperature probe
F3 - E2 - Oven temp too high
Replace temperature probe
F3 - E3 - Clean temp too hot
Replace temp. probe
F5 - E0 - Check door latch
F5 - E1 - Check door latch
Replace switch if defective

WHIRLPOOL Polara models 5 digit codes:

F1 F0 - EEPROM communication error
Replace ERC
F1 E1 - EEPROM checksum error
Replace ERC
F1 E2:7 - UL A/D errors
Replace ERC
F1 E4:2 - Model ID error
Reinsert keytail.
F1 E6:0 - Latch signal mismatch error
Replace ERC
F2 E0:4 - Shorted key error
Replace keypad assembly
F2 E1:3 Keytail unplugged
reinsert the keytail
F3 E0:5 Top oven sensor open
Test and replace top probe.
F3 E1:6 Top oven shorted
Test and replace temp probe
F3 E2:9 Bake range over temperature
Test and replace temp probe
F3 E3:8 Clean range over temperature
Test and replace temp probe.
F3 E4:10 Bottom oven sensor open
Test and replace temp probe
F3 E:15 Bottom oven sensor shorted
Test and replace temp probe
F5 E0:14 Door switch errot
Test and eventually replace door lock switch
F5 E1:16 Door latch not operating
Test and eventually replace door latch
F8 E0:17 Refrigeration error
Test the cooling module.
PF Power failure - Does not indicate a fault.
PF occurs when power is disconnected.

WHIRLPOOL
Models SF3, 30'' and 24"

F2 - Oven temperature above specifications
Check 8-pin connector from temp. probe to Electronic Oven Control
F3 - Open oven temperature probe failure
Check wiring, replace oven probe if necessary
F4 - Shorted oven temperature sensor failure
Check wiring harness, replace oven temperature probe if necessary
F5 - Push button stuck or faulty
Check for binding of pushbuttons and control panel glass. If OK, replace touch panel
F6 - Electronic control logic error (timing)
Replace Electronic Range Control (ERC)
F7 - Electronic control logic error (lock motor)
Replace ERC.
F8 - Electronic control logic error
Replace ERC.

on Jan 31, 2010 | Whirlpool RBS305PDS Electric Single Oven

1 Answer

Oven won't heat flashes F2EO and 5D on
List below does not apply to Whirlpool Models using the "Y" line in the products model numbers. Applies to models using 4 digit displays only.

F0-E0 Analog to Digital failure
Disconnect panel for 30 seconds
Should the above error re-appears, replacement of the control is required.

F1-E1 Defective ERC Replace ERC
F2-E0 Shorted Keypad. Replace Keypad.
F3-E0 Sensor or Sensor Fuse Open Replace Sensor or Fuse
F3-E1 Shorted wire or Sensor locate short and correct it or replace Sensor
F3-E2 Oven over heat Replace Sensor
F3-E3 Cleaning Temp over heat Replace Sensor
F5-E0 Door Error Check Door
F5-E1 Door Latch Check Latch
F5-E2 Door Switch Check Switch

Below applies only to the two digit display models for the brands above.
F0 Defective ERC Replace ERC
F1 Defective ERC Replace ERC
F2 Oven over heat Replace defective Sensor
F3 Oven Sensor Open Check/Replace Sensor
F4 Shorted wire or Sensor locate short and correct it or replace Sensor
F5 Defective ERC Replace ERC
F6 Problem with time keeping circuit Reset Time or cooking operation and check for proper ground.
F7 Shorted or sticking button Clean button or replace ERC
F8 Defective ERC Replace ERC
F9 Door Latch Error Check latch and latch circuit

Mar 20, 2016 | Ovens

1 Answer

What can I do for F5-E1 situation
Check this article as the cause could be the control board, the door lock mechanism or the Membrane Keypad!


Whirlpool Oven Common Problems and Causes

Jan 08, 2015 | Ovens

2 Answers

Rbd305pdb14,have error ( F5-E1) replaced controlled board, replaced touchpad, replaced sister board, replaced thermal fuse lower oven, replaced lower oven heat sensor, top oven works ok, lower oven st
That code could be the self clean latch isn't working. Try that route.

Feb 17, 2014 | Ovens

1 Answer

Rbd305pdb14,have error ( F5-E1) replaced controlled board, replaced touchpad, replaced sister board, replaced thermal fuse lower oven, replaced lower oven heat sensor, top oven works ok, lower oven still...
that's a bad door latch,if you use the self clean don't use it anymore,the oven gets up to 1000 degrees and damages the electronics in the oven,takes out the clock assy. the door latch things like that.part number WPW10195934 go here to see parts go here put model number in and look up parts,also you can check all the error codes down in bottom right hand side
https://www.searspartsdirect.com/model-number/RBD305PDB14/1198/0125300.html?searchType=modelSearch&q=Rbd305pdb14&searchTerm=Rbd305pdb14
go to upper oven and look at part number 22,you should have googled the error code before you changed out all those parts.

Feb 06, 2018 | GE JTP48SFSS Electric Double Oven

1 Answer

I am getting a E1 F5 error on the oven - what is the cause?
E1 F5 error is indicate that door latch is not working

This may display if the door is not shut properly, if it is jammed or if the spring-loaded mechanism has broken. Make sure door is completely closed and switch is closed. Test latch, solenoid and actuation switch (require an ohm meter to test).

Considerations: Try opening the oven door and shutting it while putting pressure on the center of the switch until you hear a click. Jiggle the latch to try and reposition it so that it shuts properly. Examine the latch to make sure it is properly attached.

Prevention/Solution: If none of those methods remove the error, you may need to replace the door latch. Visit the Whirlpool customer service website to find the correct part you need.

Hope this helps.

Jun 02, 2011 | Ovens

1 Answer

E1 -F5- Error code appears when attempting to start self-cleaning mode.
F5
- E1 Self clean latch will not
lock

1.
If door latched:


  1. Disconnect power from unit.
  2. Check wires and connectors from control to door switch, then from door
    switch to control. If no damage to wires and all connectors okay, proceed to
    step C.
  3. Replace door switch.
  4. Re-apply power.
  5. Press and hold any key down for 1 minute to clear F5 failure code from
    memory. F2 will appear. Press CANCEL and observe for 1 minute to ensure
    operation is correct.

2. If door not latched:


  1. Disconnect power from unit.
  2. Check wires and connectors from control to latch switch, then from latch
    switch to control. If no damage to wires and all connectors okay, proceed to
    step C.
  3. Repeat steps A and B for door switch.

3. Measure door switch (door open = switch open small low voltage terminals).
Replace switch if defective.
4. Measure latch switch (unlatch = switch open,
CAUTION - oven light contacts are closed). Replace switch if defective.
5. If
corrections are made in any step, reconnect power to control. Press and hold any
key for 1 minute to clear R failure code from memory. F2 will appear. Press
CANCEL and observe for 1 minute to ensure operation is correct.
6. If failure
remains, disconnect power and replace control.

Note:
Applies to all F5-E... codes

Dec 04, 2010 | Whirlpool RBS275PD Electric Single Oven

1 Answer

Replaced control panel on whirlpool electric double wall oven. e1 f5 code pops up,fault code says check door latch. checked switches on latch with meter check ok.what to check next
The E1- F5 error is a door lock error.

The control (TIMER) has likely failed in this instance - BUT...

Sometimes when you disconnect power to a range and reconnect it the electronic range control gets confused.
You should disconnect power again for 15 seconds and reconnect and see if that helps.

If it doesn't cure the E1- F5 error hold the bake button in until E0- F2 appears in the display.
This is the error for a stuck button on the keypad and is the way to clear the memory of the electronic range control.

Sometimes these work, but if the control has failed it won't make any difference.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.@#$RED

Feb 28, 2010 | Whirlpool RBD275PD Electric Double Oven

1 Answer

E1 F5 Error on Whirlpool Accubake Oven
The lock latch is located directly in the center upper portion of the door. It is a hook shaped latch that lock by turning downward. This lock gets stuck in this position which causes the e1 f5 error code. Locate the latch through the vent holes in the upper front of the oven door. Insert flat headed srew driver into vent hole and gently push latch up to a horizontal position & simply open door. Once unlocked, push cancel on the control panel.This will clear the error code and resolve the issue.

Apr 07, 2009 | Ovens

Not finding what you are looking for?

View Most Popular

Ovens

Related Question

I have a whirlpool accubake self cleaning oven.. when trying to use the self clean option it now states e1 f5 in the digital screen what do i do know?

  • Whirlpool Ovens

Open Questions:

0 Answers

My oven says off and can't turn it on. I was turning off the timer and accidentally turned it off. No big deal and tried to turn it back on and couldn't. Dacor wall oven

Apr 24, 2018 | Dacor Ovens

0 Answers

ACCUBAKE WHIRLPOOL checked both elements for continuity pulled the temp sensor out - unattach testing resistance ~ 1100 ohms - should be fine No errors on the control panel - does not heat, thinks it has reached 350 C - beeps and when the door is open there is no heat, both elements are cold to the touch - Turned off the breaker for 10 minutes / turned back on PF error, removed the error still no heat

Apr 23, 2018 | Whirlpool Ovens

0 Answers

miele oven model # H4780BP needs door hinge.What part # should I be getting?

Apr 23, 2018 | Miele Ovens

0 Answers

My M Spa is showing an F6 F7 error code what does that mean how do I fix it

Apr 23, 2018 | Ovens

Ovens Logo

Related Topics:

1,561 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

Kenmore 33169 Gas Single Oven

Kenmore 40494 / 40495 / 40499...

Ovens

KitchenAid Architect Series...

GE Profile JTP18 Electric...

Top Ovens Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

ashburton

Level 3 Expert

417 Answers

yadayada
yadayada

Level 3 Expert

78267 Answers

Are you an Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
90003484305.pdf. user-manual-HBN 7052...

Bosch HBN 7052 GB...

PDF Manual
SEI60MFP.pdf. user-manual-720EF...

Stoves 720EF...

PDF Manual
SEI60MFP.pdf. user-manual-720EF...

Stoves 720EF...

Loading...