Question about RCA RP8070 5-Disc CD Changer

1 Answer

Turntable. The turntable on my player will not turn. Opened it up and found the belt was cracked and not getting enough friction. Ok, problem found, but, where do I find a new belt?

Posted by on

  • Anonymous Jul 10, 2008

    i'm having a combination of this same problem, and the tray won't open. how did you remove the top? i'm stuck at the front corners, there are posts that prevent me from sliding it open, and i can't pull them up to slide them out.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 104 Answers

Measure the total length of the belt, and I presume it is square. approximate the thickness and contact turntableneedles.com, they have about 450 belt sizes in stock.

Posted on Feb 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The turntable started dragging and now the record won't finish because it stops. What's wrong ? do I need a new turntable motor? Everything else seem to be working fine thxs David


Is this a cd player or a turntable recordplayer ???

cd player that drags usually mean theres a misalignment in the tray that holds cd

turntables that drag unless they are direct drive usually need there rubber drive tires replaced or a belt what ever it has

Oct 23, 2015 | CD Players

1 Answer

Kenwood DP-R892


May be a broken belt. See if the turntable lifts out. There may be a circlip that holds it in or turn the player upside down taking care with the arm not to damage it. If the base comes off you may be able to see the belt. They are usually only the size of a skinny elastic band. If your turntable is a direct drive ( No belt) the motor may have failed.

Jun 27, 2014 | Kenwood CD Players

1 Answer

CD Changer won't finish loading a CD


I had the same problem and found the cure for it. The drive belt was streched and when it started to close on the disc, the belt would slip and eventually show loading error..The two belts cost $4.50 at belts plus. Hope this helps you

Feb 21, 2013 | Sony MegaStorage CDP-CX355 300-Disc CD...

1 Answer

The door to the turntable will not open and the turntable just keeps trying to change. Had to unplug it to make it stop.


There is a problem with the rubber belt that drives the door of the turn table. Open the cd player and replace the rubber belt.

Nov 17, 2010 | Onkyo CD Players

1 Answer

I have a Rowe R-89 jukebox. Even though the motor is turning on the turntable, the turntable is not moving. Should there be a washer on the turntable base to elevat it so it will turn?


Hello Robert,

You say you have a R-89 jukebox and the turntable motor is running, I assume that the pulley on the top of the motor is clearly seen turning. Is the turntable belt loose or missing?
From your message I am not sure that your jukebox is a R-89, could it be a 1978/1979 R-82 or R-83 that uses an idler wheel.
On this model the turntable motor is 110 volts AC.
If the above is true check that the idler wheel and the linkage spring is pulling the idler wheel against the turntable and the motor shaft.

Regards
Alan Hood
ami-man
UK
alan-hood@datex.co.uk

Aug 19, 2010 | Wurlitzer Jukebox CD Player

1 Answer

The turntable is not revolving at the correct speed slowing the record down


Sounds to me like your belt is streched. Under the felt of the turning section, there should be two rather large holes. Insert your thumb and forefinger and pull the table off. You should also see where the existing belt is running. Insert new belt around the motor first and replace the table section. Now, through the two holes, manouver the belt onto the table section until it spins freely

May 16, 2010 | Crosley CR49-TW Tweed Traveler Turntable...

1 Answer

Turntable wont turn


Lift platter and refit belt. Styluscity@gmail.com

Dec 12, 2009 | Crosley CR49-TW Tweed Traveler Turntable...

1 Answer

Belt came off on my crosley cr49 record player


1) Remove the platter - just lift up
2) Underneath the platter, you'll see a small lip section
3) Wrap the belt around this lip
4) Put platter back on turntable
5) Rotate platter until you see the motor shaft through the holes on the platter - a brass round looking piece
6) Pinch the belt around the motor shaft.
7) That's it.

- OPTiC
MasterTech
Digital Analog Therapy
Turntable Parts : Turntable Repairs

Aug 29, 2009 | Crosley CR49-TW Tweed Traveler Turntable...

3 Answers

I have a old antique wurlitzer and the records are playing very slowly what can be causing this


Bad drive belts.
Motor needs servicing (most likely).
Hasn't been converted for 50 Hz.


Dave F.

Nov 26, 2008 | Wurlitzer Jukebox 1015 One More Time...

1 Answer

Turntable is wacky


try loading half your discs on one side of the turntable and the other half on the other side and see if that solves it.

Jan 18, 2008 | Sony MegaStorage CDP-CX355 300-Disc CD...

Not finding what you are looking for?
RCA RP8070 5-Disc CD Changer Logo

Related Topics:

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA CD Players Experts

Steve

Level 3 Expert

3287 Answers

John
John

Level 2 Expert

473 Answers

The Knight
The Knight

Level 3 Expert

68301 Answers

Are you a RCA CD Player Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...