Question about Electrolux Washing Machines

1 Answer

I have an Electrolux EW1083 model, today whilst trying to start a load, there was no water forthcoming and afterwards when asked to spin, there was insufficient power to to do so. Can you please help me

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Electrolux Master
  • 8,220 Answers

Never worked on your model. I would check for a loose connection on the power cord or receptacle.If all of that was good I would look for corrosion on terminals to the door locking mechanism, motor control, and central control. I am in Alabama. That model number is not familiar to me. You can go to a site for a manual HERE
Password: tips
User: service
Don't tell nobody ok? LOL

Posted on Sep 13, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is my eiflw55hiwo electrolux front load washer not properly draining the water at the end of the wash cycle?


hmm sounds like as if any water sensors arent working as they should inside the washing machine's basket or the diagnostic board isnt getting the right info from its sensors in the washing machine's wash tub

Aug 22, 2017 | Electrolux Washing Machines

1 Answer

My top load electrolux washer machine, model MEX731CAS3 does not drain. it spins well and the cycle gets completed except the draining and centrifuging part. any suggestion?


The function of the pressure switch in the machine that gives a signal if the washing machine is full or empty with water.Spining cycle will start only if the machine is previously drain water and pressure switch overlapped to the empty position. Check everything about pressure switch and hydraulic circuit (tube and pressure chamber).

Dado

Jun 25, 2015 | Electrolux Washing Machines

1 Answer

Why doesn't my front load washer complete the spin cycle?


Good Morning Friend,

I understand that your Electrolux washer will not complete the spin cycle. I will be more than happy to assist you. I suggest resetting your appliance, by either unplugging it or shutting the power off at the circuit breaker, for 3-5 minutes. Restore power and try any cycle. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your washer status has changed successfully. If further troubleshooting is needed, I please ask that you leave the model number of your washer in your response. Hope this is helpful.

-Best Regards-
WP

May 30, 2014 | Electrolux Washing Machines

2 Answers

My washing sent in control panel alarm is ( EHO) what problem model ( zanusssi zwf 16581w)


C\nt find a fault code EH0. EH1 EH2 AND EH3 all relate to power supply problems voltage to high or low . the electronics dont like a dirty supply spikes and fluctuations upset them. they dont always work from a small generator supply.

Jul 25, 2010 | Zanussi ZWF1650W Front Load Washer

3 Answers

My electrolux ewf 1481 front loader wont spin


Open the flap, bottom right of the front panel and check the filter is clear. Most machines will not spin until they have expelled all the water. You may want to check the hose is not block and any connections to the sink if it's not on a standpipe.
Most new machines have quite sensitive out of balance detection so if it an odd load try again but add a few extra items to allow the machine to distribute the load evenly prior to spin. Hope this helps

Jul 07, 2010 | Electrolux Washing Machines

2 Answers

One minute left


be sure water is draining out before spin starts if necessary remove bottom panel and clean pump out and ck hoses to pump be sure there are no excess suds ..wash only full loads small loads or loads with 1 heavy item will cause washer to sense off balance and try to balance load this will extend cycle time

Nov 09, 2008 | Whirlpool GHW9400 Front Load Washer

1 Answer

Kenmore washer


Has it stopped agitating completely now or does it start each time then stops? Do you hear anything - say like a humm when you try it afterwards. Dose it spin/drain water from washer?. Post a response so we could know what next

Regards

Sep 01, 2008 | Kenmore 24032\24036 Top Load Washer

1 Answer

Not spinning after first 3 second spin on start.


You need a new PCB. THis happens often on these machines.

Nov 23, 2007 | Electrolux EW1200i Front Load Washer /...

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Electrolux Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Tim Whalen

Level 3 Expert

3074 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Are you an Electrolux Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...