Question about Washing Machines

1 Answer

Hi, Machine starts but stops continually during first wash cycle. Cycle selected is wash, rinse, spin. Fills for first rinse cycle but goes no further then machine beeps continuously. Fuzzy logic display is lit up at all times but seems is trying to default to full soak,wash,rinse,spin cycle. Clothes were removed and by turning machine on and off over a couple of hours, water eventually emptied. This is third wash in a row problem has happened. Thanks in advance. Regards, Ian

Posted by on

  • lls7506ian Sep 13, 2010

    Hi,



    The machine is a fuzzy logic top loading NEC NWTL656.



    Thanks

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,554 Answers

There is no more convenient and effective troubleshooting of a machine other than knowing first the exact model number of the machine. We may not be able to help you determine and address the problem unless the exact model number of the machine is stated explicitly. Troubleshooting may push through only when the exact model number of the is known. You may have stated it in your previous exchange of messages with a fellow expert, if there's any, but I cannot view the transcript of those.

You don't have to accept or reject and rate this post to add information or post comments and follow-up questions should you need further assistance. But accepting a solution does not stop you from communicating with an expert. You may continue communicating with the expert as long as you need assistance regarding the issue stated herein.

Posted on Sep 13, 2010

  • Jahn27
    Jahn27 Sep 13, 2010

    Remove the top panel to access and check the connections on the control and the fuzzy logic display including the wiring connection at the pump itself. Reseat the connections several time to clean off dirt and corrosion built-up in the connectors and the terminals. Make sure the wire harnesses are fully inserted. There seem to be an intermittent operation of the machine particularly the pump as stated in your problem description and indicated by the pump eventually emptying the water after turning on and off the machine. Turning off the machine resets it but unplugging it for at least an hour may reset the machine completely and resolve the intermittent operation problem.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I fix washing machine to finish emptying during rinse and spin cycle?


Long shot, but does it fill the same as when new? I would check the atmospheric switch which is a hollow tube that runs down the inside of the drum(not in the wash cage) when the water fills, It pushes air up to stop the fill. It may have gotten clogged. Or partially clogged.

Mar 28, 2016 | Fisher and Paykel Washing Machines

1 Answer

Ge washing machine fills up with water on spin cycle


Sounds like the timer is screwed... Sending out the wrong signals and the dryer is doing the rinse cycle when it should just be the spin cycle. Do t know what your timer looks like in that washer but most now days look like the picture. 11_11_2013_2_52_52_am.png

Aug 16, 2013 | Washing Machines

1 Answer

Fisher and Paykel 7.5 washing machine keeps powering off during rinse and spin cycles


The pump has a thermal safety cut out on it.
If the pump gets too hot it cut out.
Just put a new pump in and your all going again.

Aug 05, 2012 | Fisher and Paykel Washing Machines

1 Answer

Washer wont drain. fills with water. goes through wash cycle but wont drain. once it gets to the spin cycle, it spins for a few seconds and then stops and rinse light comes back on.


Hi,

Problems with a washing machine not spinning or not draining are often interrelated..

If you are having a problem with your top load washer then check out thistip...

Washing Machine does not Pump or Spin


If you are having problems with your front load washing machine then checkoutthis tip...

Front Load Washing machine not draining and or not spinning


heatman101

Apr 21, 2011 | GE Washing Machines

1 Answer

My frigidaire front load washer will start a wash, complete the first cycle but then stop and flash all the lights and beep continously until I press "start" or "cancel". If I press "start" again it just...


Hello there:
If your cycle does not complete or The cycle doesn't advance
When the cycle should advance, it's probably the timer or a cold-water supply problem: It's the timer, if your washing machine fills with water and begins agitating, but the timer never advances--or if the washer is in a spin cycle and the timer won't advance. Then you need to replace the timer. It may be a cold-water supply problem, if the washing machine fills with water, agitates, drains, and spins, but then doesn't fill with rinse water. than check the cold water supply line and the filter

Aug 15, 2010 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Spin/drain cycle won't start


If the timer gets to the rinse cycle and stops,
Check the lid switch for continuity. If no continuity replace the lid switch.
If the timer continues through rinse and spin without doing either, replace the timer.

May 21, 2009 | Kenmore Washing Machines

1 Answer

Frigidaire (LTF2940E) Washer starts, stops, starts, stops...


The cycle doesn't advance When the cycle doesn't advance, it's probably the timer or a cold-water supply problem:

  • It's the timer, if your washing machine fills with water and begins agitating, but the timer never advances--or if the washer is in a spin cycle and the timer won't advance. Then you need to replace the timer.


  • It may be a cold-water supply problem, if the washing machine fills with water, agitates, drains, and spins, but then doesn't fill with rinse water. See There's no cold water.

May 07, 2009 | Frigidaire GLTF2940ES Front Load Washer

1 Answer

Rinse water fills the washing machine when the spin cycle starts


Check your outlet filter, most likely it is blocked, preventing the water from draining out. Chk your pump too. Before this disconnect from the wall socket; and also check the pipe coming from the tub to the filter. Siphon out the excess water from inside the machine before you open the pipes.

May 17, 2007 | Frigidaire FGX831C Top Load Stacked Washer...

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

yadayada
yadayada

Level 3 Expert

75005 Answers

Brad Brown

Level 3 Expert

15441 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...