Question about Kenmore Oasis HE 27082 Top Load Washer

1 Answer

After u start the washer, it sprays the water and then it stops and shows an f1. Please advise.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 15,935 Answers

The F1 error code on this washer indicates a Primary Control Board failure.

It is likely that the machine control board will need to be replaced to correct this problem.

The part number for the machine control board is undetermineable because you have not provided me with the exact model # of your washer.

The procedure for replacing the machine control board is provided HERE
LINK: http://media.fotki.com/1_p,wfgstgtftbtkrrdxgtqsskgwtqkq,vi/gfsfgfsgqxgfqtqtgwf/1/1303472/5961857/image55806img-or.gif

NOTE: Be sure to unplug the washer to disconnect electrical power before accessing internal components.

There is a slight possibility that a problem with the pressure switch hose could be causing this problem.
A pinched or twisted air hose can cause this fault code.
When you open the console, check the air hose connected to the pressure switch on the machine control board.
If it is pinched or crimped, I recommend rerouting the hose to resolve this problem.
This may fix your problem without replacing the control board.

NOTE: You may want to check for this condition before ordering the control board. Most electronic control boards cannot be returned for a refund or credit.

If you find no apparent problems with the air hose on the pressure switch, then replacing the machine control board on this washer should correct your problem. There is a risk involved in replacing this part yourself.
As noted above, you could have a problem with the air pressure hose that is not apparent upon your initial inspection. A service technician would normally need to properly and thoroughly diagnose this problem before replacing the control board.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for helping with your FREE question

Posted on Sep 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My washer stops &and F-20 appears on viewer. Whats wrong with my washer


water problem check screens in hoses and valves !! rrors F1, F11 and F20
  • Error F1 indicates a communication error between the computer and the washer. Unplug the washer for a minute and plug it back in, as this may correct the problem. Error F11 indicates a motor control error. It can be caused by improper voltage. Unplug the washer and check the connections. This may fix the problem. Error F20 indicates lack of water entering the machine. If there is no water in the washer, check that the water valves are turned on. If there is water in the washer, press "Stop" twice to drain the washer. Unplug the machine and check the hose connections.


Read more : http://www.ehow.com/info_12006668_error-messages-kenmore-he2-plus.html

Feb 21, 2015 | Kenmore HE2 Plus Front Load Washer

1 Answer

Not enough water stays in machine to cover clothes We know this is an econosaver but wife likes to saok whites in total water Tried adding water by the bucket while washer is stopped but it automatically...


Hello, Thank You for using FixYa. I will be helping you today.There is no way to change the water level. It washes by spraying the water over the cloths as it moves around.
Thank You and please rate my answer if it was helpful..

Jun 12, 2011 | Maytag Bravos 3.8 Cu. Ft. Washer

2 Answers

When the water runs inside the washer always show the F1 and the machine stop.


Hi,

The "F1" error code on the Whirlpool cabrio is quite common, and generally has to do with the control board. Replacing the control panel may resolve this issue. However, I believe Whirlpool is aware of the F1 issue with the Cabrio, and is fixing some machines for free. Please call 1-800-253-1301 for more details and see if you are eligible for a free repair.

Sep 16, 2010 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

Machine stops several times shows F1 code


this is a main control board failure and needs to be replaced

Sep 16, 2009 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

Code F1


Hi. this is a serious control fault that incorporates many situations. This (F) code calls for a service call. there may be a combination of control and motor faults here. if you own a multimeter(ohm), i would start by testing the control panel connections. if you are uncomfortable with disassembling this machine, i suggest making a quick service call. If you have any questions,please feel free to ask.

Please rate and god bless.

Mar 25, 2009 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

Washer is showing a code f1


press PAUSE/CANCEL once to clear code. press start.if code reappears call for service

Mar 23, 2009 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

Whirlpool Cabrio F1 code


have the same the washer show F1 I have to hit pause start 3 time befor it will wash severly people have the same proble with this whirlpool washer it is a tiner proble i hve been tool.

Jan 24, 2009 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

Fisher and paykel water leak


Code F1 indicates that Flood switch has been
activated which explain why you feel that it is overfilling.

Water leaking
Drain hose disconnected
from waste pipe.
Reconnect the drain hose to the waste pipe.
Supply inlet hose not
properly connected.
Ensure the inlet hose is connected securely.
Other leaks. Turn water and power supplies to the
Dishwaher off.

Mar 30, 2008 | Fisher and Paykel Fisher Paykel Intuitive...

Not finding what you are looking for?
Kenmore Oasis HE 27082 Top Load Washer Logo

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Sal DeAngelo

Level 3 Expert

2183 Answers

fordexpert

Level 3 Expert

5522 Answers

Ed Mac

Level 3 Expert

731 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...