Question about Leeson Reversible Electric Motor 3/4 HP

Open Question

I need a wiring diagram to connect a Leeson motor Catalog #110087.00 to a Bremas switch CY0178262000

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a diagram to wire a Leeson motor A6C34XC28A to 115 volt


The wiring diagram may have to be requested directly from Leeson.

Apr 15, 2017 | Pool & Spa

1 Answer

New leeson 3 hp motor for my tablesaw has very little torque, and is less powerful than my old 1hp craftsman motor. What could the problem be?


If the motor is a 115/230 volt motor and is running on 115 volts but the wiring is configured for 230 volt operation, the motor will be weak.

Apr 05, 2014 | Leeson Table Saw Motor - 113627

1 Answer

I have a leeson 5ghp air compressor motor i am connecting it to a puresor switch ther is a T1 a T2 and a P1 wire i need to know where the P1 wire gos


Pressure switches usually have two or four connections. All they are are the in and out terminals for the switch or switches that the pressure sensor activates. They are usually labeled to keep them separated between in and out but it doesn't make much difference to the motor.


The multipurpose pressure switch may have a common (C), normally open (NO) and a normally closed (NC) terminal, three screws to put wire on. If this is what yours has and you have a 120VAC system, you need to attach the "hot" wire to the common terminal and one lead from the motor to whichever other terminal has continuity to the C terminal when the pressure is low, if you don't have a meter, just hook it up and if it doesn't work right move the lead to the motor to the other one. Nothing will be connected to the other terminal. The Neutral power wire will go directly to the motor.


If you switch has four terminals (two switches inside) you can attach both the neutral and the hot to one set of terminals normally labeled L1 and L2. These terminals NEVER connect to each other through the switch, they always connect to the output terminals, normally labeled T1 and T2 or any other designations desired.



If you have a 220VAC motor, you still only have two leads to the motor and they connect the same way with a two switch, four terminal set up. You would connect the two hots to L1 and L2 and the two motor leads to T1 and T2 (if so labeled).

If this doesn't help, add a comment and I'll try to explain it some more.

Sep 30, 2012 | Electric "Leeson Air Compressor Motor - 5...

1 Answer

I have Delco Model 2J2424r1, frame 56R, Series A84, phase 3 electric motor. What is the wiring diagram to run it under 230VAC?


If it has 9 leads and is a 240/480 volt motor the 1and 7 go to line 1. the 2 and 8 leads go to line 2 and the 3 and 9 leads go to line 3. the 4 5 and 6 leads are hooked together with a wire nut. To reverse rotation simply reverse any 2 of the line leads.. Prairie Dog........

Jun 15, 2011 | Leeson Reversible Electric Motor 3/4 HP

2 Answers

My boat lift electric moter was replaced... it now run slow or needs a manual assist to start... what is the problem? Current level?


check input voltage check to see if its the proper phase check tension on belts, gear, or connection from motor

May 28, 2010 | Leeson Reversible Electric Motor 3/4 HP

1 Answer

How to conect 3 phase motor 9 yellow wires from p1


Connect t4,t5,t6 together. Connect t1,t7 together for line 1. Connect t2,t8 together for line 2. Connect t3,t9 for line 3.

May 23, 2010 | Omega 5hp 1740RPM 184TC Frame 230 Volts...

1 Answer

I have a 3/4 HP motor installed on my porch chairlift that has stopped working. The motor only hums when you push the up or down button. After removing the motor it spins freely and will run but has no...


it is possible that the start/run winding is open cicuit or cable connections via the capacitor you mentioned , is it distorted , any sign or leakage . as it is on a stair lift the motor has to be reversed , is the reversing switch intact.

Ian c

Dec 21, 2009 | Leeson Reversible Electric Motor 3/4 HP

1 Answer

I need a diagram to wire it to a saw


should be a wiring diagram on the wiring cover.

Oct 25, 2009 | Leeson Reversible Electric Motor 3/4 HP

Not finding what you are looking for?

Open Questions:

See all Leeson Reversible Electric Motor 3/4 HP Questions

Leeson Reversible Electric Motor 3/4 HP Logo

Related Topics:

539 people viewed this question

Ask a Question

Usually answered in minutes!

Top Leeson Tools & Hardware - Others Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Brad Brown

Level 3 Expert

15950 Answers

J.D. Browning
J.D. Browning

Level 3 Expert

2760 Answers

Are you a Leeson Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...