Question about Sport & Outdoor - Others

2 Answers

When i switch my power trek treadmill it gives constant beep with this message, tried reset button and all i can think of, but no luck

Posted by on

  • 4 more comments 
  • b mothe Sep 12, 2010

    ER07 problem on powertrek treadmill

  • b mothe Sep 12, 2010

    thanks for your info, it is giving ER07 message when switched on, i will try the websites suggested in the meantime. Power Trek treadmill, basic model no number on the machine i bought it 4 yr ago

  • b mothe Sep 12, 2010

    thanks, model number is not available, it is basic powertrek treadmill model, it gives ER07 on turning on power button and reset or anything else wouldnot actually switch on the machine. it keeps on beeping, thats all

  • b mothe Sep 19, 2010

    it says ER07 when switched on and doesnt start, powertrek treadmill it has no model no on it

    many thanks

  • b mothe Sep 19, 2010

    sorry it is ER 07 on starting, and keeps beeping, the machine acutually start,
    thanks
    sid

  • b mothe Sep 19, 2010

    tried the site but no fix so far, machine says er07 on switchng on but doesnt actually start

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,777 Answers

What message does it give you, I think you forgot to include that in the question. Also what model number of treadmill is it?

Thanks
Tim

Posted on Sep 13, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Sport & Outd... Master
  • 3,083 Answers

Not sure what exactly is happening, but here is a good general troubleshooting page that should help you:
http://www.treadmilldoctor.com/Troubleshooting
You didn't mention the error message or model number, so I couldn't find any specific information on the treadmill.
This is the general site for information and tips:
http://www.treadmilldoctor.com/;jsessionid=0rlNMNDY11VyNjjyztRkpt1GJgWfJ0Z2Cc710X5Rl0CLJwDz07Gf0n9p65vhhxTCF47Tfsmb12QvLnpGTFv2QGJ7CyzbqHT6LvRLW4hTmFSwJTyTY9QpYPTWKs3RGN5f!-120111630?gclid=CO6djYKrgqQCFQhbagodrEjqHg
Good luck, hope this helps, and thanks for using FixYa.

Posted on Sep 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wont turn on


Was it damp down there?

Mar 26, 2015 | Office Equipment & Supplies

1 Answer

Power go to treadmill but won't turn on


Try for a repair manual: manualslib.com
Are there batteries somewhere, that are dead and corroded? Another type of an exercise device I had was like that. Otherwise, the power supply to the boards and or the drive system may have expired.

Mar 26, 2015 | Office Equipment & Supplies

1 Answer

Treadmill not working and alarm sound when plug in


Does the display give you an error code. I'm having a similar issue but all LEDs on my display are lit with a constant beep and still have not gotten resolved. Have you tested the power source and fuse and the reset circuit breaker. I am waiting on a new reset circuit breaker part to come in and hopefully this fixes the issue. I will let you know.

your posting is a year old have you since got the treadmill fixed and what was it

Mar 29, 2014 | Bremshey RN7 Folding Treadmill

1 Answer

Horizon t207


follow this steps and fix it. God bless you

1.
    • 1
Unplug the treadmill. Locate the console key and place the safety or reset key into the treadmill console. Replace any parts that need replacing, or is large enough to trigger with a pencil eraser or Q-tip. Plug the treadmill plug back into the wall. Use the Q-tip to press the reset button. It may be necessary to hold the reset button down for a few seconds. "CL11" will appear in the display of the treadmill.
    • 3
Press the reset button one more time with the Q-tip. "CL21" should appear on the screen. Press the enter key. The display will change again and show "CL22." Keep pressing the enter key until the numbers cycle through to the number "CL26." Press enter one more time. The letter E should appear on the display screen.
    • 4
Press enter twice more. The letters "SS" should appear on the screen. When this happens, press the start/stop key. Making sure to keep well away from the tread, press enter to start the treadmill. The treadmill will start on its own. The treadmill will stop on its own after a few seconds. When it stops, press the power key two times. Remove the safety key and put in a safe place. Your treadmill is reset.move on to the next step.
    • 2
Locate the reset switch on the underside of the treadmill console. Usually the button

Oct 08, 2013 | Horizon Exercise & Fitness

1 Answer

Treadmill Error Codes


you must reset the error. Try to adjust the REED SWITCH, clean it, test for open or faulty, and tight the cables very well.see the diagram attached. Adjust to the speed sensor, do the same like reed switch, see the diagram attached,

Run the software calibration, for easy diagnostica, and fix it.

God bless you3e434441-57bf-4020-8417-a2f42a9c4ac4.gif056477ca-c697-409a-ba80-a7544469dd90.gif

May 23, 2013 | Exercise & Fitness

1 Answer

PLO5 error message on Quinton Clubtrack treadmill


Try to clear the error message. God bless you

1 )Locate the reset switch on the underside of the treadmill console. Usually the button is large enough to trigger with a pencil eraser or Q-tip. Plug the treadmill plug back into the wall. Use the Q-tip to press the reset button. It may be necessary to hold the reset button down for a few seconds. "CL11" will appear in the display of the treadmill.


  • 2

Press the reset button one more time with the Q-tip. "CL21" should appear on the screen. Press the enter key. The display will change again and show "CL22." Keep pressing the enter key until the numbers cycle through to the number "CL26." Press enter one more time. The letter E should appear on the display screen.

  • 3

Press enter twice more. The letters "SS" should appear on the screen. When this happens, press the start/stop key. Making sure to keep well away from the tread, press enter to start the treadmill. The treadmill will start on its own. The treadmill will stop on its own after a few seconds. When it stops, press the power key two times. Remove the safety key and put in a safe place. Your treadmill is reset

Jan 25, 2013 | Quinton Stairmaster Clubtrack 3.0 GymTough...

1 Answer

Lifetrack OMA-117 treadmill constant beeping not moving


1) adjust the REED swithc , see the diagram clean , and tight the wires connector very well.

2)Try to RUN the software calibration for diagnose, and troubleshooting.

God bless you
6_30_2012_1_23_13_am.gif

Jun 29, 2012 | Exercise & Fitness

1 Answer

The machine just goes into auto calibrating on the screen and beeps constantly. does not stop auto calibrating Just seems unable to cope with any programs to do with hill climbs


power off, put in the key, press and hold down the 'stop' button and 'incline up' buttons, power on holding down the buttons for a few seconds - message clears

Feb 17, 2011 | Tunturi T60 Folding Treadmill

2 Answers

Screen states Lube Belt , do not have user Manual , Where are lubrication points and what type "lube" can I use ?


hi,


It is necessary to lubricate your treadmill running deck every six months or 150 miles to maintain optimal performance. Once the treadmill reaches 150 miles, the console will display the message "LUBE" or "LUBE BELT". The treadmill will not operate while the message is showing. Hold Stop for 5 seconds to suspend message for 5 miles. Your treadmill came with a bottle of lubricant which can be used for two applications. If you need lubricant, contact Horizon Fitness. Only use lubricant provided by Horizon Fitness.

• Turn off the treadmill with the on/off switch, then unplug the power

cord at the wall outlet.

• Loosen both the rear roller bolts. (For best results, place two removable

marks on both sides of the frame and note roller position). Once the

belt is loosened, take the bottle of lubricant and apply it to the entire

top surface of the running deck. Tighten both rear roller bolts

(matching up the marks for proper position) to original position. After

you have applied lubricant, plug in the power cord, insert the safety

key, start the treadmill and walk on the belt for two minutes to spread

the lubricant.

• Lubricate the air shocks with Teflon based spray.
• Once lubrication is complete, reset the console by pressing and holding 'STOP' and Speed '+' buttons for 5 seconds.
ok

Dec 26, 2010 | Horizon T91 Treadmill

2 Answers

Horizon treadmill won't start running


The manual said that after lubricating the deck, press Stop and Speed buttons together for 5 minutes and this will reset the lubrication message and the treadmill should work.

Jan 25, 2010 | Horizon Exercise & Fitness

Not finding what you are looking for?
Sport & Outdoor - Others Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sport & Outdoor - Others Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

kakima

Level 3 Expert

102366 Answers

Brad Brown

Level 3 Expert

16010 Answers

Are you a Sport and Outdoor - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...