Question about GE Security DVMRe-16CT-600 16-CHANNEL Color Triplex Multiplexer-Recorder with 600-GB Hard Drive, Ethernet

1 Answer

No Audio I cannot get any audio from the unit. The audio speakers playback audio, none is being recoorded.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 34 Answers

Check in the settings and make sure it is selected to be on.

Posted on Aug 24, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I record audio onto the SD card?


what is the model of the cam?

some cams only do video
depends what its saving the file as
may be your software that wont play the audio but plays the video ok
check the codec used to save the audio

Apr 26, 2015 | SWANN Surveillance Cameras

1 Answer

Why are continuous recording graphics grayed out when trying to export data?


make sure that you choose the start and end time just like it appear at playback

May 06, 2014 | Bosch DVR 600 SERIES 8 CH VIDEO 4 CH AUDIO...

1 Answer

I need the total wiring diagram for camera [8pin rj11]


8 pin RJ45 (8P8C) male connector
at the camera output

LG LVC-CY100NM Color Security Camera with 8-pin RJ45 (and other cameras for the LSP-M1017M Dual Quad Observation Systems by LG)
Pin
Number Pin
Name Description 8 SPK Speaker (Hot) 7 VID Video Out 6 GRN Ground 5 SPK- Speaker (cold) 4 AO Audio Out/Alarm Out 3 VDC 12VDC 2 N/C RS-485- 1 N/C RS-485+ Note: Pin numbers are labled backwards in the manual (corrected above).
The camera is adaptable for use in any composite video application with the use of a balun.
on the output. I had noise-less video and clean audio across a 350 foot run of cat 5e.

Jan 29, 2013 | LG LVCCy100NM Color Security Camera with...

1 Answer

My Lorex SV-01-RCV Wireless A/V instructions were lost in our move and I need help with the set up. Could you please help? I can not remember the correct connection.


You should have a 2-wire cable with Yellow, White and Red RCA plugs on each end.

The Yellow line is video out.
The White line is Left channel audio out.
The Red line is Right channel audio out.

Since your RCV only has two RCA jacks use the Yellow line for video and the White line for audio.

You should also have an "F-connector for co-axial cable.
If your TV set does NOT have audio and video jacks hook that to the co-ax antenna connector on the back of your TV set.
Set the RCV for either channel 3 or channel 4 and do the same with your TV set.

The RCV unit has four receive channels which must match up with the channel selected on the CAM or TX unit.

You can scan all four channels either by auto or manual.

If you only have one CAM or TX unit it probably doesn't matter which of the four you use unless you have a computer ROUTER which interferes with one of the four channels.

If so, select the 1, 2, 3, or 4 channel which has the least or no interference manually.

Bil Munsil
K1ATV HAM TV
Mesa AZ
Hams should be seen as well as heard.


Dec 30, 2009 | Surveillance Cameras

3 Answers

4-wire surveillance camera wiring diagram


Cut wires Blue whight yellow orange wires go to what on a security camera

Jun 20, 2009 | Surveillance Cameras

1 Answer

Audio


This may be a feedback issue if you are playing bsck the audio from the camera in the same room the camera is located in. Turn down the speaker volume or turn them off.

Jun 05, 2009 | D-Link Securicam Network DCS-950G Wireless...

1 Answer

Samsung shr-1040 playback is blocky


Sorry, but there is no way to turn off the compression. That is the just the way a quad works. It compresses the 4 video signals to 1 channel. The only way to get around it is to buy a 4 channel unit. 1 channel per camera.

Rob

Jan 24, 2009 | Samsung SHR-2082 8 Channel Stand Alone Dvr...

1 Answer

Dvr4-alert full screen playback


That's because this is a quad. It compresses all 4 video feeds into 1 file. When you play it back, it decompresses the video and shows you each camera. Playback through this unit is the only way to see 1 camera at a time. 
To be able to copy 1 camera shot to a DVD, this is what you need to do: You need to have a TV with Video in and Video out jacks.  Connect the Quad to the TV Video in jack and connect the TV Video out jack to your DVD Video in jack. Playback a single camera shot on the quad to the TV and hit record on your DVD. - The DVD will record whatever is shown on the TV. 

Oct 26, 2008 | Surveillance Cameras

Not finding what you are looking for?
GE Security DVMRe-16CT-600 16-CHANNEL Color Triplex Multiplexer-Recorder with 600-GB Hard Drive, Ethernet Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Surveillance Cameras Experts

Coss

Level 3 Expert

1039 Answers

Brad Brown

Level 3 Expert

13529 Answers

ka4iup
ka4iup

Level 3 Expert

3944 Answers

Are you a GE Surveillance Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...