Question about Whirlpool DU930 Built-in Dishwasher

Open Question

Whirlpool DU1300: control panel sensor board does not work. can push any button or combination of buttons and DW does not operate. Please Help

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 262 Answers

SOURCE: my dryer wont start

check and see if you have 220 volts to your dryer using a volt / ohm meter find the cord and remove cover take meter and go across (1 test lead on left and one on right) side of cord there should be 220 volts.check this and get back to me. if no 220v trip breaker back and forth and try again

Posted on Dec 29, 2007

Ad
  • 3422 Answers

SOURCE: Whirlpool dishwasher won't work at all

Hi,

If your dishwasher doesn't work at all, check these:

Power from the house Is there power getting to the dishwasher? This can be difficult to test, because dishwashers are usually wired directly to an electrical circuit, rather than plugged into the wall. But at least check for a blown fuse or a tripped circuit breaker.

Door switch The door switch is important because, if it's defective, the dishwasher won't work at all. To reach it, you need to remove the control panel cover, or sometimes the interior liner of the door. If it's defective, you need to completely replace it.

Wiring Often the main wiring connection from the house, at the dishwasher, burns and breaks the connection. If that's the problem, the wires must be repaired/replaced as necessary. If that's not the problem, check the wiring to the door switch, the wiring between the door and the lower part of the dishwasher, and the wiring to the timer. Repair any broken, burned, brittle, or defective wiring, using the proper appliance-grade wire and connectors.

Timer or selector switch Although it's uncommon, the timer or the selector switch may be defective. If so, you need to replace the defective part, because neither of these can be repaired.

Posted on Aug 07, 2008

  • 1028 Answers

SOURCE: Whirlpool 9400 Front Loader Washer Control Button Locked

find button with lock emblem beside it hold 3-5 secs

Posted on Oct 09, 2008

tzweeb
  • 318 Answers

SOURCE: push start button on control panel - machine does not start

only 2 things can cause this.
1 the control is set to lock out mode. just hold the lock button for 5 seconds and it should go back to normal mode.
or 2 the controls user interface has an internal failure. its the part that has the switches and tells the computer what to do. either way call whirlpool and see if its still covered by their warranty.
of yeah and the 3rd thing is you have no power to unit. make sure the outlet is good by trying something else in the same outlet, like a light or hairdryer.

Posted on Jan 06, 2009

breddi2
  • 126 Answers

SOURCE: The Controls Locked button is on and nothing works

Most whirlpools you just hold lock button for a few seconds and it will return to normal function.

Posted on Apr 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Nothing works on control panel except control locked sensor light. The buttons were working fine then I went to add more drying time and the buttons do not light up or work.


From the details of your symptom you're indicating a possible intermittent loose connection between the user interface (touch panel) and the machine control board or the voltage supply to machine control board at P1 connector.

Disconnect the power cord from the power source.

  • Disconnect P3 and P4 connectors from the machine control board and then reconnect them.
  • Disconnect P1 connector and then reinstall the P1 connector and then recheck operation.

If the wires are good then you will need to replace the control board on your unit.
Here is a link to the part.


Jan 09, 2011 | Whirlpool Duet 7.0 Cu. Ft. Capacity Plus...

2 Answers

I have had a Haier Dishwaher ESD300 for about 2 years. It suddenly just stopped. None of the buttons will work. I have checked fuses etc. All of that is fine. Wondered what I could do to fix the problem.


My dishwasher had the exact same symptoms. The control panel was faulty. I discovered this by testing the connector with my multimeter, looking for the LED connections. When I wasn't able to find anything, I carefully peeled it off. (See picture.) I expect at least one of the traces underneath the nasty brown line is faulty, causing the control panel to not function. On the control board, I jumpered the first pin to the fifth pin from the bottom of the connector, as viewed with the Haier brand right-side up, and pots & pans started right up.
flszen.jpg.
It looks like I can get a replacement control panel from Sears Parts Direct for $30.

Dec 28, 2010 | Haier ESD300 / ESD301 Built-in Dishwasher

1 Answer

I moved my washer and then moved it back. The status shows control locked. How do I get it back operational


The "Control Lock", this is actually a safety feature that enables the consumer to lock the control panel to prevent small children from manipulating the controls and accidentally starting the appliance. This can usually be reset and does not require a technician.

With the lock on, the control panel is disabled and you cannot use any of the controls, except the button that unlocks it. Using the STOP or CANCEL buttons will not turn the feature off. It can inadvertently be set following a power outage, leaning against the control panel, or pressing and holding the wrong button. This is usually not an indication of a malfunction.
While you were moving the washer, you may have been pushing on the some of the control panel buttons and locked the control panel.

If this is a Whirlpool manufactured appliance (such as Kenmore Elite, Whirlpool Duet or Maytag Epic), the following link explains how to lock/unlock this feature:

http://www.fixya.com/support/r3608801-control_panel_lock


These instructions are also printed on the front panel of the appliance and in the owner's manual.

If this does not correct your problem, then you may have a more serious problem than a simple operator control button issue (such as an operator console problem or main control board issue). Please post back and let me know if you need further assistance.

May 15, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Range will default to 165 degrees


HI, You will need to check the oven sensor wires that link the actual sensor to the main control board. Make sure that the contacts are connected properly, and not loose, or corroded. If all the wiring checks out, test the sensor for the correct resistance readings.(you will need a multimeter for this test)

The most common oven sensor should be approximately, 1100 ohms when at room temperature. The others may be close to as follows:

100°F - 1143 ohms
200°F - 1350 ohms
300°F - 1553 ohms
350°F - 1654 ohms
400°F - 1753 ohms
500°F - 1949 ohms

If the sensor test is adequate, and the wiring is Ok at the control, this will lead to a failed control board. replace the control in this case.

Dec 07, 2009 | Kitchen Ranges

1 Answer

I have Jandy RS4 system with 4-button poolside controls for additional spa control. Inside house control panel stays totally lit up saying ''Rev 6700'', and cannot communicate or control pool operations. ...


Pull the cover off the control panel. You will probably find a button which would be accessible from outside the panel with a paper clip or pencil but is unlabeled. On the board itself by the button, in small letters it should say "reset". Push the button and see what happens.

Oct 07, 2009 | Jandy Aqualink - Rs24 One Touch Pool / Spa...

1 Answer

BUTTONS ON CONTROL PANEL DOESN'T WORK REGULARLU


HI, unfortunately, the actual part you need(Control board), has been discontinued. it is best to just purchase a newer unit in this case. This unit is not repairable at this time due to the unavailability of the components.

Aug 06, 2009 | Whirlpool RMC275PD Microwave Oven

1 Answer

Push buttons stubborn, don't always work


If this is the Membrane type (touch button) you usually will have to replace the entire strip as a replacement.

Mar 23, 2009 | Whirlpool Gold 24 in. Built-In Dishwasher...

1 Answer

Blinking quick rinse and lock on lights


Try holding down the "lock" button.It may be the way to unlock the problem.

May 26, 2008 | Kenmore 16602 / 16604 / 16609 Built-in...

1 Answer

Pause mode stuck


Is the door firmly closed? Open the door and close it firmly. If the pause button is really stuck, you will need to repair/replace the board.

Oct 17, 2007 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Whirlpool Calypso Dryer Electrical Problem


Problem resolved. Although the membrane control panel passed the diagnostic test, it was defective. Probably a low voltage conductor went to ground, allowing the buttons to operate but throwing the control board into error mode.

Oct 08, 2007 | Dryers

Not finding what you are looking for?
Whirlpool DU930 Built-in Dishwasher Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Mike

Level 3 Expert

4340 Answers

Owen Barnes

Level 3 Expert

867 Answers

Are you a Whirlpool Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...