Question about Reebok Acd1 Treadmill Motor Control Board 141877

1 Answer

UNIT DOES NOT POWER UP. I CHANGED THE POWER BOARD WITH NO RESULTS. POWER BOARD 120 VOLT LIGHT IS ON. 9 VOLT DC LIGHT IS ON. PWM & TACH LIGHTS ARE NOT LIT. CONSOL DOES NOT LIGHT UP

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

If its a Icon Health and Fitness branded treadmill (proform,image ,healthrider etc.)The safety key activates the on off switch for the console. (micro switch activated by safety key)Check for 9-12v going to console. Unless it has a magnet switch. What brand and model ?

Posted on Sep 16, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Plugged camper into 120 volt everything works electrically except ceiling lights dont work


* Check 12 volt DC system (may be camper battery or car battery, though most only use the camper battery.)
* Camper may be using 12 volt DC lights so it can be turned on while your on the road or not hooked up to an 120 VAC or 240 VAC outlet.
* If you are using 120 VAC lights then check the neutral line (note; HIGH voltage here. Get help from an electrician or at least the RV park handyman.) The problem may be at the outlet (the RV site's problem) or more likely in your plug or cable (the big cord) as it does get abused, run over, kinked, etc. Need to have it checked by an electrician.
* Check the light bulbs; is it seated properly? Replace if burnt out. Have electrician test if there is power at the socket.
* Final; Be safe and have a qualified electrician service your camper.
Aloha, ukeboy57

May 11, 2018 | Electrical Supplies

2 Answers

Too much power and now lorex camera wont turn on


CAMMERA DESTROYED !! MOTION LIGHTS USE 120 VOLT AC POWER
CAMERAS USE 12 VOLT DC POWER

WRONG TYPE AND AMOUNT OF POWER !!!

Jan 16, 2014 | Lorex Home Security

1 Answer

I have a herritage t101, it displays the Ls error and has no drive whatsoever but was working a few month back


The SCR lower board is designed with diagnostic LED lights. The LED's are color coded according to
their specific function. Green indicates a properly operating treadmill; the green lights should always
be ON when power is supplied to the treadmill. Yellow indicates a treadmill function. Red indicates a
treadmill malfunction. Here is a list of each LED and what it signifies:
MOTOR (yellow) - The MOTOR LED illuminates when dc (direct current) voltage is sent to the drive
motor. The LED gets brighter when the dc output is increased.
RLC (yellow) - The RLC (R = Reactance / L = Inductance / C = Capacitance) LED illuminates when
the filtering system is properly working. The filtering system includes the capacitor and filter choke. If
there is a short in either component then the RLC light will not come on.
DN & UP (yellow) - The DN and UP LED lights tell us if the elevation DN and UP relays are
functioning properly. When the LED lights, it tells us that the relay has energized and is sending high
voltage (110vac or 220vac) to the elevation motor.
AC PWR (green) - The AC PWR (Alternating Current Power) illuminates when AC line voltage is
delivered to the treadmill. It then passes through the in-line fuse (110)/s(220) and lights the AC PWR
LED.
+12V (green) - When the proper AC voltage is delivered to the treadmill, passes through the in-line
fuse/s, through the full wave bridge rectifier (changes AC to DC), through the transformer (steps down
DC to +12vdc) then the +12V LED lights.
This the board LED, who control the signal for Main Motor+Elevation Motor. You must see, the LED DN+ UP( both will be Lit) in any position down or Up.
2) The RELAY board is designed with diagnostic LED lights. The LED's are color coded according to
their specific function. Green indicates a properly operating treadmill; the green lights should always
be ON when power is supplied to the treadmill. Yellow indicates a treadmill function. Red indicates a
treadmill malfunction. Here is a list of each LED and what it signifies:
AC PWR (green) - The AC PWR (Alternating Current Power) illuminates when AC line voltage is
delivered to the treadmill. It then passes through the in-line fuse (110)/s(220) and lights the AC PWR
LED.
VDC (green) - The VDC LED will light when it receives DC voltage from the DC power supply.
DN & UP (yellow) - The DN and UP LED lights tell us if the elevation DN and UP relays are
functioning properly. When the LED lights, it tells us that the relay has energized and is sending high
voltage (110vac or 220vac) to the elevation motor.
UPSW (green) - This LED will illuminate when the low voltage dc is delivered from the upper display
board to the elevation UP relay. This low voltage dc is what energizes the coil of the relay.
DNSW (green) - This LED will illuminate when the low voltage dc is delivered from the upper display
board to the elevation DOWN relay. This low voltage dc is what energizes the coil of the relay.
BELTSW (green) - This LED will illuminate when the low voltage dc is delivered from the upper
display board to the belt (motor start) relay. This low voltage dc is what energizes the coil of the relay.
SPD (yellow) - The SPD LED flashes on and off (relative to speed) when the speed sensor is
operating properly.
PWM (yellow) - This LED will light when the upper board is sending a speed signal to the PWM.
Both the PWM LED and BELTSW LED must be lit for belt movement.
Finally this this Relay Board, the Each Led will be Lit, for any Relai control for DN down, or UP elevation motor. Use the contact cleaner, you can find it in R .Shack.
see the diagram attached.
God bless you1_14_2013_9_25_21_pm.png

Jan 14, 2013 | Exercise & Fitness

1 Answer

I have a reebok crosswalk rt 5.0 treadmill. I can calibrate the incline and it goes up and down. however when you press the button to raise the incline the incline number will change but the machine does...


Step 1:

see this details and proceed according. God bless you

The SCR lower board is designed with diagnostic LED lights. The LED's are color coded according to

their specific function. Green indicates a properly operating treadmill; the green lights should always

be ON when power is supplied to the treadmill. Yellow indicates a treadmill function. Red indicates a

treadmill malfunction. Here is a list of each LED and what it signifies:

MOTOR (yellow) - The MOTOR LED illuminates when dc (direct current) voltage is sent to the drive

motor. The LED gets brighter when the dc output is increased.

RLC (yellow) - The RLC (R = Reactance / L = Inductance / C = Capacitance) LED illuminates when

the filtering system is properly working. The filtering system includes the capacitor and filter choke. If

there is a short in either component then the RLC light will not come on.

DN & UP (yellow) - The DN and UP LED lights tell us if the elevation DN and UP relays are

functioning properly. When the LED lights, it tells us that the relay has energized and is sending high

voltage (110vac or 220vac) to the elevation motor.

AC PWR (green) - The AC PWR (Alternating Current Power) illuminates when AC line voltage is

delivered to the treadmill. It then passes through the in-line fuse (110)/s(220) and lights the AC PWR

LED.

+12V (green) - When the proper AC voltage is delivered to the treadmill, passes through the in-line

fuse/s, through the full wave bridge rectifier (changes AC to DC), through the transformer (steps down

Step 2:

This the board LED, who control the DC to +12vdc) then the +12V LED lights.
signal for Main Motor+Elevation Motor. You must see, the LED DN+ UP( both will be Lit) in any position down or Up.

2) The RELAY board is designed with diagnostic LED lights. The LED's are color coded according to

their specific function. Green indicates a properly operating treadmill; the green lights should always

be ON when power is supplied to the treadmill. Yellow indicates a treadmill function. Red indicates a

treadmill malfunction. Here is a list of each LED and what it signifies:

AC PWR (green) - The AC PWR (Alternating Current Power) illuminates when AC line voltage is

delivered to the treadmill. It then passes through the in-line fuse (110)/s(220) and lights the AC PWR

LED.

VDC (green) - The VDC LED will light when it receives DC voltage from the DC power supply.

DN & UP (yellow) - The DN and UP LED lights tell us if the elevation DN and UP relays are

functioning properly. When the LED lights, it tells us that the relay has energized and is sending high

voltage (110vac or 220vac) to the elevation motor.

UPSW (green) - This LED will illuminate when the low voltage dc is delivered from the upper display

board to the elevation UP relay. This low voltage dc is what energizes the coil of the relay.

DNSW (green) - This LED will illuminate when the low voltage dc is delivered from the upper display

board to the elevation DOWN relay. This low voltage dc is what energizes the coil of the relay.

BELTSW (green) - This LED will illuminate when the low voltage dc is delivered from the upper

display board to the belt (motor start) relay. This low voltage dc is what energizes the coil of the relay.

SPD (yellow) - The SPD LED flashes on and off (relative to speed) when the speed sensor is

operating properly.

PWM (yellow) - This LED will light when the upper board is sending a speed signal to the PWM.

Both the PWM LED and BELTSW LED must be lit for belt movement.
Finally this this Relay Board, the Each Led will be Lit, for any Relai control for DN down, or UP for elevation Motor. You must clean contact of the Relay with Special Spray(Radio Schack).

With this you must fix it.

Jan 07, 2013 | Reebok Exercise & Fitness

1 Answer

2003 gulf stream prairie schooner 5th wheel computer box/electrical problem


ac runs off 120 volts refrigerator 120 volts heater element 12 volt heater element and control board outside lights 12 volt ceiling fan 12 volts wires that go to box 2 blue furnace 12 volt wires from thermostat 12 volt

May 10, 2017 | RVs

1 Answer

Generac 5500XL, model#09778-7 no output. Changed the power regulator board. No luck. Flashed the 120 plug with 12-30vdc from DC board. Nothing. Excited the brushes directly with DC board. Only got 2.36VDC...


Double check your brush istallation. positive side toward rotor bearing, if you put 12 vdc directly into brush pack and check with a meter at the 120 vac outlet and have low or no voltage, you may have no resistance in your rotor slip rings, excitor & main windings also need a resistance check. 12.6-16.7 ohms (rotor) 2.26-2.80 ohms (excitation) .26-.32/.28-.35 main or power windings. Note: unit running when appling 12 volts to brush pack. 2-5 second only, ( This test tells you the rotor & stotor are ok )

Jan 22, 2010 | Coleman Powermate 5000W Home Backup...

1 Answer

No power, no lights on laptop


I think you should check the real power supply ... 120 V in and what comes out ... volts (ac - dc) and amps or what fraction of an amp.

Please compare the old with the new power supply. The new power supply should be the same volts - same kind (AC or DC) and at least the same amp rating. You can use higher amp rating but not lower - lower will burn up - literally)

Volt meter ... always set it above the suspected voltage. Batteries are always DC. Houses, buildings, etc always AC. Power supplies - could be mixed - ac in and dc out.

So if you were measuring in your home, you set the meter to 130 or higher on the AC scale. If you were doing your auto, 24 volts DC (or so).

House current, probe color doesnt make any difference. Should read about 120 Volts between the narrower (or right side/ground down orientation) or the two slots and the wider of the two shots (wide should be the neutral side - ground on the bottom). You can prove the hot side by measuring to the ground. White wire to ground = no reading. Black wire to ground = 120 volts. (The black and white are INSIDE the electric outlet. You can use either probe to do the measurement.

I hope this helps you.

If you have more question, please let me know.

Thanks for using fixya.com

a

Oct 23, 2009 | E-Machines M5309 Notebook

1 Answer

Reebok rx3000 treadmill. panel lights up fine. 2 of the 10 speed buttons will not imput and the start button will not start the treadmill. checked the power panel. led lights to voltage light up fine, but...


it is two items in this case. The light on the PWM will light if you force the belt to move. I would start with a lower board replacement. If it works fine then you need a new console. I have seen this when people use the heart touch bars on the treadmill and get a static shock. this can ruin the console.

I’m happy to help further over the phone at https://www.6ya.com/expert/howard_079189dd4959a511

Apr 18, 2009 | Reebok 8050 ES Treadmill

2 Answers

DeWalk DC500 wet/dry vaccum doesn't work


Vacuum works with the battery but does not work with 120 volt. Every time I plug it in it blows the internal fuse. I have replaced the fuse inside the vaccum several times and every time i plug it in it blows. What do you think it could be?

Feb 21, 2009 | Dewalt DC500 Canister Wet/Dry Vacuum

Not finding what you are looking for?
Reebok Acd1 Treadmill Motor Control Board  141877 Logo

574 people viewed this question

Ask a Question

Usually answered in minutes!

Top Reebok Exercise & Fitness Experts

Matt Olenzek
Matt Olenzek

Level 2 Expert

297 Answers

Ross Metcalfe
Ross Metcalfe

Level 2 Expert

129 Answers

Howard
Howard

Level 2 Expert

115 Answers

Are you a Reebok Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...