Question about Miele Coffee System

1 Answer

Getting error message "fit jets in central spout"

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

You need to pull down the metal thingy in the middle where the coffee comes out of (the thing that goes up and down to accommodate different cup sizes). Pull off the front plate, then put it back on and make sure it slides all the way up. The message goes away.
ML Spider

Posted on Jun 06, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When using the shower a strong water jet comes out the hole at the bottom reduce img the water power what can I do


If by "hole at the bottom" you're talking about the spout that fills the tub, and you must pull up on a knob on the top of the spout, then its an easy and inexpensive fix. The knob is the diverter and the seal is worn out. Replace with a new one you can buy at any hardware store. I suggest you remove the old one and take it with you as there are two pipe sizes. A strap wrench or large pair of channel lock pliers will do the job easily. Just grab the entire spout and twist counterclockwise, OR if there is a small hole on the underside of the spout, then a 1/8 or 3/16 Allen wrench will loosten the set screw that holds the spout on, then just wiggle as you pull on the spout to remove

Jul 28, 2016 | Jet Home

1 Answer

Our bathroom faucet spoutpopped off how to fix


If it is a tub spout it is probably what is known as a slip-fit. Look under the spout. There should be an allen key there. Loosen it, slide the spout back on and tighten it. I recommend tightening it with the allen key is the upright position until it starts to get tight. Then spin the spout so it points down and finish tightening.

May 18, 2016 | Plumbing

1 Answer

Coffee makers Miele cva 4066 stuck on fit jets in central spout


You might need to reset the coffee maker by turning it off and then turn it on again.

Apr 28, 2015 | Miele Coffee Makers & Espresso Machines

1 Answer

Turn on machine get message


I found this solution in an old posting, credit to Brian Hammet:

Pull the stainless steel dispenser cover straight down as far as it will go. now push it firmly up as far as it will go. if the error message still appears, repeat, but push up faster and harder. there is a switch monitoring the position of the central jets to make sure they are installed. you have to push up hard enough to close that switch. sometimes you have to slam it pretty good, but dont go crazy on it. just give it a firm touch.

Nov 29, 2013 | Miele Dishwashers

2 Answers

Service manual for "Insert water spout" problem


Check the heating coils for proper resistance or no resistance. If the machine is sending a signal to check the coils before turning them on AND it is not getting any resistance then it cannot continue. However if you have the machine plugged in near the microwave oven, then a power surge may have blown the control board or caused it to lose its progamming. The control board is expensive!
http://www.appliancefactoryparts.com/smallappliances/delonghi/esam5500-b-perfecta.html

Nov 24, 2013 | DeLonghi ESAM5500

1 Answer

My machine says " fix


It says fit jets in central spout, not fix. The stainless steel cover over where the coffee comes out sits on top of the central jets. pull the dispenser down as far as it will go. Now pull it straight out to you. reach up and grab the black plastic piece that holds the central jets. pull it straight down. Now fit the central jet housing into the stainless steel cover. put the cover back on and push it firmly up into place. if it still says fit central jets, pull the stainless steel cover down and slam it up a little harder. there is a switch up inside that needs to feel the presence of the central jets so it doesnt spray coffee and milk everywhere. You should be cleaning those jets every 24 hours anyway. Get the manual out and go through the maintenance proceedures. that milk will start to turn into green cheese if you dont clean the jets and pipework every night.

Jul 14, 2011 | Miele Coffee System

1 Answer

Miele coffee machine is stuck on a demand. "Fit jets in central spout" what do i do and how do i fix it???


pull the stainless steel dispenser cover straight down as far as it will go. now push it firmly up as far as it will go. if the error message still appears, repeat, but push up faster and harder. there is a switch monitoring the position of the central jets to make sure they are installed. you have to push up hard enough to close that switch. sometimes you have to slam it pretty good, but dont go crazy on it. just give it a firm touch.

Jul 01, 2011 | Miele Coffee System

1 Answer

Tub spout, cannnot lift up lever for shower, has seized up, what can be done


Hi,
The tub spout can be replaced very easily....
Check if it spins off (threaded) or if there is a allen set screw that you get to from the bottom of the spout....the spout will then just pull off....
They sell new spouts at Home Depot, Lowes, or Plumbing Supply houses....the universal spouts will fit either configuration...

heatman101

Mar 08, 2011 | Kohler Home

1 Answer

Water comes out spout and shower head at same time


Hello gruber d, you need a new spout. When a spout is working properly you raise the knob on top and it slides a baffle over the outlet at the spout. Once the water is blocked from flowing out of the spout it forces water up and out of the shower head.
You may also remove the spout and see if you can get a closer look and see if you can make some kind of adjustment to it.
Removing the spout;
1. Put a cloth around the spout to protect the finish.
2. Adjust a pipe wrench to fit over the spout and the cloth.
3. Turn the spout counter-clockwise to loosen.
My goal was to provide timely and accurate information. If this has been helpful to you, please
consider taking a second to click on the, " this was helpful ", button.
Than you!

Jan 13, 2011 | Grohe Grohmix Thermostat Valve & Trim -...

1 Answer

Lisbon monobloc kitchen taps just installed the


Put some cooking oil around the o-rings to sofen them up so they would seat around all fitting surfaces. Hope this helps.

Aug 12, 2010 | Home

Not finding what you are looking for?
Miele Coffee System Logo

3,430 people viewed this question

Ask a Question

Usually answered in minutes!

Top Miele Coffee Makers & Espresso Machines Experts

Jerry Greenberg
Jerry Greenberg

Level 3 Expert

1667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

steve morris
steve morris

Level 3 Expert

1675 Answers

Are you a Miele Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...