Question about Masterbuilt M30BV Deep Fryer

1 Answer

I can't keep my flame lit and can't figure out how to make it work please help asap

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 193 Answers

Sometmes the regulator needs to be reset. Follow these steps exactly. Turn off the gas valve at the burner. Turn off the tank valve. Slowly turn the gas tank valve on. THEN turn on the valve to the burner. Be aware that the wind will blow this burner out fairly easily as well. It may be necessary to locate the burner out of any possible drafty areas.

Posted on Sep 09, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Gas ignites with lever ignition but when lever is released gas cuts out


I can't tell what kind of appliance you're talking about.... but, here's what I know.. This "lever" you're talking of kind of stumps me, but try, after the gas lights, to hold the lever in the position you had when you lit the flame. Hold it on for about a minute... then release it... and see if the flame will remain going. If you can't keep the flame going "no matter what", you probably need to clean or replace the flame sensor.

Nov 14, 2013 | Valor Toys

1 Answer

I changed my thermocouple on my fireplace,it still wont stay lit


Thermocouple keeps the pilot lit.
Thermopile keeps the burner lit.
Please specify what won't stay lit...
If it's the burner, you may need to change the thermopile as well.
If the pilot still won't stay lit, you will want to make sure that the pilot flame is large enough to completely engulf the thermocouple and keep it hot. If it's too small, you may need to take some compressed air and blow out the pilot hood to remove any blockage.

Dec 18, 2012 | Napoleon 36" Zero Clearance Top/Rear Vent...

1 Answer

American range msd 1 wont stay lit


There is a flame sensor at the ignitor, you may want to clean it first and re-try see it help...good luck

Sep 04, 2012 | American Range Majestic M1GLP Stainless...

1 Answer

I was just wondering my rotisiree burner dosent work .. please help asap! thanks


If it is not igniting and hold the flame and getting red, it could be that the burner is dirty and clogged or the thermocouple that keeps the burner lit has failed.Please keep in mind, when lighting an infrared burner, you must hold the burner control knob in for several minutes. At least until all the ceramic plaques are glowing brightly. if the igniter won't light it, try match lighting it, while you hold the burner control knob in.

Most gill manufacturers recommend lighting and burning the infrared rotisserie burner on a regular basis, whether you use it or not,. Doing this helps to keep the burner clean.

I hope this has helped you and thanks for choosing FixYa.

Sep 14, 2011 | Grilling

1 Answer

The ignition kicks on and gives a flame but goes out after 30-45 seconds then starts up all over again. What is going on with it. Its a power vent. It is quite windy outside due to a blizzard going on....


Hi,
The flame sensor is dirty or bad...it is not telling the control that the flame is lit...



Here is a tip that will help you try to figure out why your furnace is not working.

Basic Furnace or Heating System Troubleshooting

heatman101


Feb 02, 2011 | Heating & Cooling

2 Answers

Pilot ignights, keeps sparking then goes to lockout


I have the exact same model with the exact same problem. Did you ever figure out what the problem was? I just picked up a new gas valve, but maybe i should check the flame sensor first. In my systems case the electronic ignition fires, which lights the pilot, but it keeps firing even though the pilot light is lit. So I think it could be the flame sensor, how do I remedy that or check it out. I would like to check this out first before dropping in the gas valve, cause they arent cheap and I can still return it before its installed.

Jul 11, 2010 | Raypak Free Hydraulic Lift Gate Delivery -...

1 Answer

Wall mounted CBN30T, pilot goes out


IF its balance flue it could be blocked . Burner or orifice blocked lack of air to pilot slightly blocked thermocouple defective .

Mar 03, 2017 | Desa International CBN20T Heater

1 Answer

Gas Dryer Problem


I would change both coils anyways,they can go bad after they heat up.

Nov 02, 2008 | Whirlpool Dryers

1 Answer

Stove-top burners


Hi,
Here is a tip that I wrote that will help figure out why the burner spark keepson clicking...

Gas Range RepairBurners Keep on Clicking
heatman101

bvn

Jul 10, 2008 | Belling 27 in. CTC465 Electric Cooktop

Not finding what you are looking for?
Masterbuilt M30BV Deep Fryer Logo

Related Topics:

175 people viewed this question

Ask a Question

Usually answered in minutes!

Top Masterbuilt Kitchen Appliances - Others Experts

Richard Lilja
Richard Lilja

Level 3 Expert

381 Answers

Angel Joseph Jr.
Angel Joseph Jr.

Level 2 Expert

683 Answers

Sock Puppet

Level 3 Expert

241 Answers

Are you a Masterbuilt Kitchen Appliances - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...