Question about Jacuzzi MAGNUM POOL PUMP 1-1/2 HP MAGNUM PUMP BY

1 Answer

I have a mt2000-h magnum pump, but did not get the controlls with the pump. Im trying to figure out how to get the two speeds out of the motor when i only have one set of motor leads for the 220v hook up. motor data tag says 1750-3425 for motor rpm. how does this motor produce two differant rpm's without two differant sets of windings?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 990 Answers

You have two windings if it is two speed. What you need is a switch
before your wires come into the motor you need to take one of the leads and run it through a high low switch. This will simply take one of your 110v lines and make it go to high and low speed on the motor.
Green will go to ground, one 110v line will go to common and the other goes to the switch. It comes out as two leads. One will hook up to the low speed terminal and the other will hook to the high speed terminal in the back of the motor.

Posted on Sep 09, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My electric motor went bad and i am trying to replace it but can't remove it from the pump housing


you do not want to replace the motor only, the pump is handled as a unit... there are seal issues, etc.

Sep 05, 2010 | Jacuzzi Magnum Force Series Pool Pump 1...

1 Answer

How do you get the pump out of the housing on a jucuzzi magnum force pump


If yours is the model with the big round ring around motor, it is a large retaining nut. Remove this nut and the motor should come from the pump housing. Don't be too rough, plastic breaks.

Jun 27, 2010 | Jacuzzi MAGNUM FORCE POOL PUMP - TWO SPEED...

1 Answer

Hi I have a magnum 1000 Jacuzzi pump for my


alot of companies use to have a damper ring on pump shaft which would knock down some of the noise a pump motor made pumps make noise and the bigger the pump the louder the noise if its not vibrating or clunking then its running as it should

Apr 21, 2010 | Jacuzzi MAGNUM FORCE POOL PUMP - TWO SPEED...

2 Answers

Push on button and it motor just clicks.


impeller stuck or seized-- motor needs to be oiled--or relay bad --check power to motor if power relay ok --need to service or repair impeller or motor

Feb 16, 2010 | Jacuzzi MAGNUM FORCE POOL PUMP - TWO SPEED...

1 Answer

Jacuzzi Magnum 1000 - overheating & looking for manual


Loosen the motor and impeller from the pump by backing off the large plastic nut and take that whole section to an electric motor repair shop for inspection. If the motor is salvagable, they can quote the repair or replacement.

Jul 05, 2009 | Jacuzzi MAGNUM FORCE POOL PUMP - TWO SPEED...

1 Answer

Pump noise


sounds like it needs new bearings, take it to a pool professional.

Jun 04, 2009 | Jacuzzi MAGNUM 2 SPEED POOL PUMP 2.0 HP

1 Answer

Getting to impellre


the impeller is what is holding it in on the end of motor is the impellel the impeller is in a houseing right off motor that is held togethere by screws you should disconect power then power for motor then remove water in/outtake there may be some kind of strap holding it down

Feb 25, 2009 | Jacuzzi MAGNUM FORCE POOL PUMP - TWO SPEED...

2 Answers

Jacuzzi magnum pool pump impeller broke


The impeller on the Magnum pump unthreads counter clockwise as do other impellers. There is a shaft of the motor that runs the length of the motor, on the back of the motor when you take the bell housing off you will see a small silver spot with a **** in it for a standard screwdriver. Put the biggest one in there you can and then grab the impeller and turn it counter clock wise and it should unthread. Sometimes they won't if it has been on there a number of years. You will need to break it off if it doesn't unthread. Then just purchase a new Impeller for the Jacuzzi Magnum Pump.

Rod
US Parts Center

Feb 24, 2009 | Pool & Spa

2 Answers

Pump will not work in high speed


Only three posible problems. High is out on pump. Spa side control is out. Control box relay that runs high pump is out.Does upper controls(spa side) read out a code? Kirk

Feb 12, 2009 | Jacuzzi MAGNUM FORCE POOL PUMP - TWO SPEED...

Not finding what you are looking for?
Jacuzzi MAGNUM POOL PUMP 1-1/2 HP MAGNUM PUMP BY Logo

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jacuzzi Garden Experts

john h

Level 3 Expert

12650 Answers

Jay Finke
Jay Finke

Level 3 Expert

1363 Answers

Ian Kime
Ian Kime

Level 2 Expert

77 Answers

Are you a Jacuzzi Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...