Question about Briggs & Stratton Electrical Supplies

1 Answer

Briggs and stratton 8000 watts generator, the output of the 120 is only 102. How do I adjust the output?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Briggs & Str... Master
  • 1,388 Answers

Voltage is adjusted by increasing rpm of engine. Use meter with Hz setting and try to adjust to 60 cycles and check voltage to be at about 115-120. If engine is turning 3600rpm/60 cycles and voltage is very low, then problem is most likely with brushes/ commutator rings, or voltage regulator. Some voltage regulators have an adjustment screw to bring voltage up/down (adjust to proper rpm/cycles first). Good luck

Posted on Sep 09, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Briggs 6200 elite generator. Starts runs good no ac output and display is blank


http://www.ebay.com/itm/BRIGGS-STRATTON-GENERATOR-OPERATORS-MANUAL-ELITE-SERIES-6200-RUNNING-WATTS-/401042177246 $14.95

May 30, 2016 | Briggs Electrical Supplies

1 Answer

Need wiring diagram,from alternator to plug-ins for briggs & Stratton (3500) Elite series Model # 030208-0


No wiring diagram available from Briggs. Try re-magnetizing the rotor. No AVR or Capacitor listed in the parts list.

Disconnect the wires to brushes ( pay attention to the order) and apply 12vdc to brushes. Positive goes to brush closest to the bearing. Start the generator and check for output. If output is normal run the unit a few minutes to ensure re-magnetization then shut down normally. After shut down disconnect the 12 vdc source and re-install the previous disconnected wires. Now re start the generator and test for output should be okay provide there is no problems with the alternator. If no output during the above re-magnetization then your rotor windings my burned out.
25208236-xjbiib4t2p1wjuzy4gozn52g-4-1.png

Oct 10, 2014 | Briggs & Stratton Gas Powered 3500-4375...

1 Answer

Briggs & Stratton Briggs Stratton 6200 Watt Portable Generator voltage adjust


Usually the cause of slightly low voltage like this is that the engine is not running at full operating RPM. Find the high speed adjusting screw on the govenor linkage and adjust the engine RPM until the output is 220V - 240V

Dec 09, 2013 | Briggs & Stratton Briggs Stratton 6200...

1 Answer

Honda generator leaking gas from carborator


that is your fuel drain screw so if you get any water in your carb you can drain it and it was loose thats why gas drained out of it

Dec 16, 2012 | Briggs & Stratton Measuring Tools &...

1 Answer

Briggs & Stratton 12KW Model 040229 LPG Generator. 96 Volts @ the 120 Volts outlet, When I turn the house 2 Ton AC voltage increase to 106 Volts.


Can you manually adjust the voltage on the generator without load?? If you have 120/240 60hz output on it and you are not overloading the unit (amperage), then it may be as simple as adjusting whats called your gain setting for your voltage regulator. Obviously you are seeing what happens when it is set too low. Trying raising that setting until it becomes unstable then back it off. Unstable meaning voltage starts jumping all over.

Jun 27, 2011 | Briggs & Stratton Briggs Stratton 7 kW...

2 Answers

No power output from Briggs & Stratton ProMax 7500E generator


You may have exciting field broken. Look for a fuse or wire break.

Jun 04, 2010 | Briggs Stratton Portable Generator 305cc...

Not finding what you are looking for?
Electrical Supplies Logo

Related Topics:

623 people viewed this question

Ask a Question

Usually answered in minutes!

Top Briggs & Stratton Electrical Supplies Experts

John Trevino

Level 3 Expert

1388 Answers

Falcon52

Level 1 Expert

18 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you a Briggs & Stratton Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...